Dimension One Spas Dynamic Massage Sequencer manual Digital Display Messages

Page 13

2002 Dimension One Spas Export Owner’s Manual

Digital Display Messages

The following messages may appear in the Digital Display:

“OH” – Overheat Protection

When “OH” is displayed on the control system Digital Display, the hot tub is in a high temperature condition. If such a condition exists, check water temperature and if it is above 104° F (40° C), DO NOT ENTER THE WATER. If this happens, remove the hot tub cover and allow the water to cool below 110° F (43.3° C). Reset the power to the spa by resetting the GFCI breaker. If the problem recurs, turn off all power to the hot tub and contact your local Authorized Dimension One Spas Dealer, or authorized service center.

Flashing LED on the Control Panel

If you see 3 flashing LEDs on the Digital Display, check the water temperature and if it is above 104° F (40°C) DO NOT ENTER THE WATER. The system has detected a problem. Check the Digital Display and if it is displaying the “OH” symbol, contact your local Authorized Dimension One Spas Dealer, or authorized service center. If the Digital Display is displaying the temperature, check the water level and clean the filters. If the problem persists, reset the power to the spa by resetting the GFCI breaker. If the error is not resolved after resetting the spa, contact your local Authorized Dimension One Spas Dealer, or authorized service center.

Flashing Temperature on the Display

If you see a flashing temperature of 34° F (-16.6°C) or 134° F (56.6°C), DO NOT ENTER THE WATER. The system has detected a problem. Contact your local Authorized Dimension One Spas Dealer, or authorized service center.

Summer Mode

The “SUMMER MODE” feature temporarily disables the circulation pump “Cool Off” cycle. During hot weather the spa can experience “Heat Creep”. Heat creep is caused when the spa, during normal maintenance operations, cannot dissipate more heat than is generated. This may cause the spa temperature to exceed the set temperature and cause a “Cool Off” cycle. In order to prevent the water from becoming cloudy due to the circulation pump being turned off by the “Cool Off” cycle, the spa can be set to bypass the “Cool Off” cycle. This is accomplished by setting the spa in the “SUMMER MODE”. To initiate a “SUMMER MODE”, use the Up and Down pads to set the temperature to 59° F (15° C). The Digital Display will indicate “SUMMER MODE”. In this mode the pump will run continuously until the water temperature reaches 107°F (41.67° C) and then turns off. It will remain off until the water temperature reaches 102° F (38.39° C) at which point the pump turns on.

Standby Mode

The “STANDBY” mode allows the user to clean the filter without turning off power to the spa. This feature disables all automatic and manual functions.

To enter the “STANDBY” mode press and hold the Dimension One Spa”s ICON logo for 5 seconds. To exit the mode, press and hold the logo for 5 seconds. If you do not exit the mode manually, the spa will automatically return to normal functionality after 24 hours.

The “Smart Winter” mode is not affected by the use of the “Standby”: mode.

Note

9

Image 13
Contents Page Page Table of Contents Surface Care Ultralife and Granitex To Reduce the Risk of Injury Important Safety InstructionsHazardous to your health HyperthermiaDo’s and Don’ts Vista, CA 92083 760 Following features are included on your hot tub Hot Tub FeaturesJet System Selector Valve NeckFlex Jet Pillow Smart Heat Available only on Dimension One SpasUltra Pure Water Management System CrystalZone Water Management SystemTop Side Control OperationDigital Display Jets Low/High Control PadDimension One Spas Icon Logo Temperature PadsProgram Pad Heat Status LightDigital Display Messages Clock Set Using the Programmable Digital ControllerFilter Cycle Start Time Filter Cycle DurationInitial Startup Temperature Unit SelectionDigital Display LCD Temperature PadJets 1 and 2 Pads Light PadEnter Pad Scrolling Message Center Digital Display MessagesRinse Filters Change Water Clean FiltersChange Vision Cartridge Spa Check UpCooling IceSetting the Time Using the Scrolling Message CenterVision Cartridge Pump Run TimeDigital Display LCD Invert Control Panel LockProgramming Unlock Control Panel ResetControl Panel Description Sequence Indicator Lights 1 through Massage Zone Indicator Lights Human FigureJets Pad Speed PadMassage Zones Massage Zone DescriptionPanel Screws Operating the Dynamic Massage SequencerMale Hose Fitting Page Filter Cleaning Routine Equipment MaintenanceLight Bulb Replacement Draining Your EquipmentSurface Care Ultralife and Granitex Dimension One EnviroTect Skirts and Vinyl CoversGranitex/Quarite Plus Special Cold Weather Instructions Procedure for WinterizingCare for the Wood Spa Cabinet Items Required for WinterizingPage Spring Time Startup Replace all equipment access panels onto the systemGranitex  /Quarite Plus  Disclaimer Warranty Service InformationTerm Definition Glossary of TermsTemperature Heating System Troubleshooting GuideElectrical System Poor Water SystemPage