Cooper Bussmann 858 Proprietary process replacement panels meet the photommetric, 5345-44J

Page 14

DOCUMENT 1025

REV. B

Instruction Manual

AGS-LED

858 LED Series

Sizes 1, 2, 3, 4 and 5

10 Maintenance and Troubbleshooting

WARNING:

WARNING

 

Remove Po wer Before Attempting Any Servicing.

 

 

 

10.1General

Work on electrical circuits should be done only by a qualified electrician with a working knowledge of airfield lighting circuits. Trouble-shooting is accomplished by meeans of process of elimination. It should be chhecked that the POWER is OFF and secured, and o nce one solution is tried, POWER is reapplied. Then POWER turned OFF and secured and another solution tried, etc. Repeat this until the prooblem is solved.

It is also assumed that the circuit is in proper working order from the isolation transformer secondary connector (L-8233 style 7or 8 receptacle) all the way to and including the power source. Use of a calibrated true RMMS-reading multi-meter with a current sensing clamp-on attachment will aid in the trouble shootting of electrical circuits. Warning: Only use OEM replacement sign legend panels

 

 

 

 

WARNING:

NOTICE

 

 

 

Only use O EM replacement sign legend panels. The entire message

 

 

 

 

 

 

 

element mu st be replaced per FAA AC 150-5345-44J 3.2.5.10.2. Our

 

 

 

 

proprietary process replacement panels meet the photommetric and

 

 

 

 

 

 

 

 

wind loadinng requirements of the sign as certified to FAAA AC 150-

5345-44J.

6

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Airside Guidance Sign AGS-LED LED Series Sizes 1, 2, 3, 4 Revisions Limited Product Warranty Safety Notices Keep Away from Live CircuitsDocument REV. B AGS-LED Test Equipment and Tools Table of Contents List of Figures and Tables Double module signGeneral Information General Description Classification of SignsPart Numbers LED Series Document REV. B AGS-LED Document REV. B AGS-LED Proprietary process replacement panels meet the photommetric 5345-44JAdhesive surfaces before installing Max. See F igure 18 Also, remover carriers from thermmal padProblem Possible Cause Corrective Action CCR Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Continue Checking the Rest of the LED Modules Replacing an LED Moddule Document REV. B AGS-LED Replacing Sign Power Supply Board & Heat Sink P/N Sign PC Board P/N 62277 CalibrationDocument REV. B AGS-LED Document REV. B AGS-LED Figures and Tables Document 1025 REV. B Three module sign Four module sign Distance Marker Sign Options Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Expanded left section of Figure Expanded right section of Figure Expanded top section of Figure Concrete Foundation/Pad configurations, Size Concrete Foundation/Pad configurations, Size Document REV. B AGS-LED Sizes 3, & 5 Concrete Foundation/Pad Configurations Size 4 Concrete Foundation/Pad Configurations Power Supply Box Power Supply Wiring Diagram Documment REV. B AGS-LED Power Supply Switch and Jumper Selection Ferro CCR Power Supply Switch and Jumper Selection Series CCR Cchalp Cchalp Style Sign Size # Modules CCR type @5.5A Xfrmr Type Series 181 Sign Sign VA Watts Power Sign Watts 108 Regulator Setting Current Range A, RMS D11 D29 Fault Red Part Description Number Used on Document
Top Page Image Contents