Cooper Bussmann 858 instruction manual Replacing an LED Moddule

Page 23

DOCUMENT 1025

REV. B

Instruction Manual

AGS-LED

858 LED Series

Sizes 1, 2, 3, 4 and 5

Turn on main power to the sign. If LED MODULES #1 to #5 momentarily light and theen turn off, then the LED MODULE #5 and the cable from the LED MODULE #4 to the LED MODULE #5 are operating normally.

WARNING

WARNING:

Failure to t urn off power to the sign and wait five minutes could result in severe injury or death.

Turn off main power to the sign. Wait five minutes for the high voltage to dissipate. Verify that Power Supply Output Voltage meeasures less than 30-VDC, as described above. Replace the black

return cable connector with the LEDD MODULE #5 output cable connector. Replace thee black return cable connector into the output connnector housing of the 6th LED MODULE.

If the sign does not light at all, then replace the LED MODULE #5 and/or the cable con necting from the output connector of LED MODULEE #4 to the input of LED MODULE #5 (see Section 10.10). Then repeat the test as described in this seection.

10.10 Replacing an LED MODDULE

In the case where an LED MODULE has failed and needs to be replaced use the following instructions:

INSTRUCTIONS FOR REPLAC ING AN LED MODULE

The following instructions assumme that the sign front face is removed and that th e failed LED MODULE has been previously iddentified.

WARNING

WARNING:

Failure to t urn off power to the sign and wait five minutes could result in severe injury or death.

1.Turn off power to the sign by tuurning off the corresponding Constant Current Regullator (CCR) power. (WARNING: Wait five minutes after sign power is turned off to servicee the sign. This will allow any residual high vooltage stored in Power Supply PCB components to bleed off.)

15

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Airside Guidance Sign AGS-LED LED Series Sizes 1, 2, 3, 4 Revisions Limited Product Warranty Keep Away from Live Circuits Safety NoticesDocument REV. B AGS-LED Test Equipment and Tools Table of Contents Double module sign List of Figures and TablesClassification of Signs General Information General DescriptionPart Numbers LED Series Document REV. B AGS-LED Document REV. B AGS-LED 5345-44J Proprietary process replacement panels meet the photommetricMax. See F igure 18 Also, remover carriers from thermmal pad Adhesive surfaces before installingProblem Possible Cause Corrective Action CCR Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Continue Checking the Rest of the LED Modules Replacing an LED Moddule Document REV. B AGS-LED Sign PC Board P/N 62277 Calibration Replacing Sign Power Supply Board & Heat Sink P/NDocument REV. B AGS-LED Document REV. B AGS-LED Figures and Tables Document 1025 REV. B Three module sign Four module sign Distance Marker Sign Options Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Expanded left section of Figure Expanded right section of Figure Expanded top section of Figure Concrete Foundation/Pad configurations, Size Concrete Foundation/Pad configurations, Size Document REV. B AGS-LED Sizes 3, & 5 Concrete Foundation/Pad Configurations Size 4 Concrete Foundation/Pad Configurations Power Supply Box Power Supply Wiring Diagram Documment REV. B AGS-LED Power Supply Switch and Jumper Selection Ferro CCR Power Supply Switch and Jumper Selection Series CCR Cchalp Cchalp Style Sign Size # Modules CCR type @5.5A Xfrmr Type Series 181 Sign Sign VA Watts Power Sign Watts 108 Regulator Setting Current Range A, RMS D11 D29 Fault Red Part Description Number Used on Document
Top Page Image Contents