Cooper Bussmann 858 instruction manual Ccr

Page 17

		DOCUMENT 1025
		REV. B
	Instruction Manual
	Instruction Manual
	AGS-LED
	858 LED Series
	Sizes 1, 2, 3, 4 and 5

PROBLEM	POSSIBLE CAUSE	CORRECTIVE ACTION

		MODULE(s) (See Sec 10.10)

(P.10) Upon	Incorrect LED Power Supply	Verify/Set Power Supply
applying power,	Circuit Board Switch	Board Switches and jumpers
sign	Configuration	are set according to Table 1
momentarily		(Ferro CCR) or Table 2 (Series
lights and then		CCR)
turns off.

(P.11) Upon	LED MODULE Voltage has	Replace any LED
applying power,	dropped 25% below the calibrated	MODULE(s) with non-lit
sign	output voltage (See Table 12).	LEDs and re-calibrate the LED
momentarily		Power Supply. (See Sections
lights and then		10.10 & 10.11)
turns off.

(P.12) Upon	LED MODULE Voltage is greater	Verify/Set Power Supply
applying power,	than 125% of the expected	Board Switches and jumpers
sign	calibrated output voltage (See	are set according to Table 1
momentarily	Table 12).	(Ferro CCR) or Table 2 (Series
lights and then		CCR)
turns off.

(P.13) Sign	Incorrect LED Power Supply	Verify/Set Jumpers JP1 and
flickering	Circuit Board Jumper Setting.	JP2 according to the Table 1
		(FERRO CCR) or Table 2
		(Series CCR)

(P.14) Sign	Incorrect Isolation Transformer	Replace with Isolation
flickering		transformer that matches sign
		type, size, #modules. (See
		Tables 3-8)

9

Image 17

Contents Airside Guidance Sign AGS-LED LED Series Sizes 1, 2, 3, 4 Revisions Limited Product Warranty Keep Away from Live Circuits Safety NoticesDocument REV. B AGS-LED Test Equipment and Tools Table of Contents Double module sign List of Figures and TablesClassification of Signs General Information General DescriptionPart Numbers LED Series Document REV. B AGS-LED Document REV. B AGS-LED 5345-44J Proprietary process replacement panels meet the photommetricMax. See F igure 18 Also, remover carriers from thermmal pad Adhesive surfaces before installingProblem Possible Cause Corrective Action CCR Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Continue Checking the Rest of the LED Modules Replacing an LED Moddule Document REV. B AGS-LED Sign PC Board P/N 62277 Calibration Replacing Sign Power Supply Board & Heat Sink P/NDocument REV. B AGS-LED Document REV. B AGS-LED Figures and Tables Document 1025 REV. B Three module sign Four module sign Distance Marker Sign Options Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Document REV. B AGS-LED Expanded left section of Figure Expanded right section of Figure Expanded top section of Figure Concrete Foundation/Pad configurations, Size Concrete Foundation/Pad configurations, Size Document REV. B AGS-LED Sizes 3, & 5 Concrete Foundation/Pad Configurations Size 4 Concrete Foundation/Pad Configurations Power Supply Box Power Supply Wiring Diagram Documment REV. B AGS-LED Power Supply Switch and Jumper Selection Ferro CCR Power Supply Switch and Jumper Selection Series CCR Cchalp Cchalp Style Sign Size # Modules CCR type @5.5A Xfrmr Type Series 181 Sign Sign VA Watts Power Sign Watts 108 Regulator Setting Current Range A, RMS D11 D29 Fault Red Part Description Number Used on Document