Bush Hog 2165 manual Lock Pins Storage Tubes, Operating the Backhoe

Page 11

Figure 3 Safety Locks

Swing Lock Pin

 

Boom Transport Lock Pin

 

 

 

SWING LEFT AND RAISE the boom by moving the control lever back and to the left.

SWING RIGHT AND LOWER the boom by moving the lever forward and to the right.

SWING RIGHT AND RAISE the boom by moving the lever back and to the right.

3.Crowd/Bucket: Push lever forward, the dipperstick moves out, away from the operator. Pull lever back, the dipperstick moves in, toward the operator.

Move lever to left, the bucket curls in. Move lever to right, the bucket extends out.

By moving the lever to one of the intermediate posi- tions, the dipperstick can be extended or retracted at the same time the bucket is being loaded or dumped.

EXTEND AND LOAD the bucket by moving the lever forward and to the left.

RETRACT AND LOAD the bucket by moving the lever back and to the left.

EXTEND AND DUMP the bucket by moving the lever forward and to the right.

RETRACT AND DUMP the bucket by moving the lever back and to the right.

The two operations of the boom/swing lever, com- bined with the two operations performed by the crowd/bucket control lever, provide four simultaneous operations from the two levers, keeping cycle time to a minimum.

4.Right Hand Stabilizer: Push lever forward, the RH stabilizer lowers. Pull lever back, the RH stabilizer raises.

Figure 3a

Lock Pins

Storage Tubes

In general, the direction of movement of a control lever corresponds to the movement of the operating member.

OPERATING THE BACKHOE

CAUTION

To avoid possible injury, observe the following safety rules WHEN OPERATING the backhoe.

1.DISENGAGE safety lock pins as shown in Figure 3 before attempting to operate the back- hoe. Store lock pins in angled tubes located at the rear right hand side of the backhoe below the foot platform. See Figure 3a.

2.OPERATE from the backhoe operator’s seat only.

3.LOWER the stabilizers until the rear of the trac- tor is totally supported by them. NOTE: Rear tires should not come up off of the ground. See dia- gram on Page 11.

4.DO NOT dig near the stabilizers.

5.DO NOT touch overhead wires with any part of the backhoe.

6.DO NOT attempt to raise the tractor off the ground or move the tractor forward or backward using the backhoe dipperstick or bucket.

7.DO NOT lose stability by swinging the bucket downhill when positioned on a slope.

8.DO NOT lower the backhoe boom using the “float” function. It will freefall, and could result in injury to bystanders or damage to the backhoe.

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Backhoes Congratulations Backhoes Table of ContentsDisclaimer of Implied Warranties & Consequential Damages This Limited Warranty Shall not Apply2165, 2175, 2185 and 2195 Backhoes Dealer Preparation Check ListYour Safety is Involved Safety Alert SymbolBackhoe Important Safety PrecautionsTractor Avoid HIGH-PRESSURE Fluids Adjustments and InspectionTransportation Osha Regulations EMPLOYERS, Employees and OperationsEmployee Tractor Operating Instructions This Act SeeksControls Keep bystanders a safe distance awayEngine Speed Operating the Backhoe Lock Pins Storage Tubes50102295 Transporting the BackhoePlacing the Stabilizers When TransportingDumping the Bucket Filling the BucketBackfilling Side Slope Excavating or TrenchingMiscellaneous Finishing Straight WallsHydraulic System Hoses ServiceBeginning of Season Bleeding Backhoe Hydraulic SystemOn Models 2165, 2175, 2185 and 2195 the follow Tooth ReplacementLubrication Tightening Nuts and BoltsRemoval from Tractor Storage Install the swing safety lock pin as shown in Figures 1Stabilizer Pads Troubleshooting ProceduresTroubleshooting Troubleshooting Load drops or settles Troubleshooting Troubleshooting Replacing Spool Seals Valve RepairReplace Center Section Assemblies General AssemblyMounting Backhoe to Tractor or Skid Steer loaders General DescriptionPoint Hitch Linkage 2165 Ag Tractor using 3-point hitchAssembly Refer to Figures 14 Point Hitch Linkage 2185/2195Assembly PTO Pump Kits Optional AssemblyDo not Remove Tractor PTO Guard Hydraulic HOOK-UP to TractorPage Closed Center System Backhoe Operation Hook-Up DiagramHydraulic Hook-Up 2175, 2185 Hook-Up RequirementsTractor Preparation Power Beyond KitsFor Tractors with OPEN-CENTER Hydraulic Systems Great Bend Backhoe & Great Bend Loader Valve Assembly Second ProcedureTractors with an auxiliary hydraulic flow of 15 gpm or less Flow Divider KIT OptionalGeneral Description Flow Divider Valve to Backhoe MountingFor Tractor Hydraulic Flow Greater than 15 GPM Testing Backhoe Hydraulic Hook-UpFlow Divider Valve to Skid Steer Adapter Mounting For Skid Steer Hydraulic For Skid Steer H Ydraulic Flow of 15 GPM or LessSeries Page Safety Decals Recommended Torque in Foot Pounds Newton Meters Torque SpecificationsBox 1039 Selma, AL 334

2165 specifications

The Bush Hog 2165 is a versatile and robust rotary cutter designed for heavy-duty lawn care and land management applications. This model is a part of the renowned Bush Hog lineup, known for its durability, efficiency, and ease of use. The 2165 strikes an excellent balance between performance and functionality, making it an ideal choice for homeowners, landscapers, and farmers alike.

One of the standout features of the Bush Hog 2165 is its impressive cutting width of 65 inches, which allows it to cover large areas quickly and effectively. This makes it particularly suitable for tackling overgrown fields, pastures, and roadside maintenance tasks. The cutter is equipped with a powerful, heavy-duty gearbox that ensures reliable performance under various conditions, providing users with the confidence to handle even the most challenging cutting jobs.

The design of the Bush Hog 2165 emphasizes user safety and comfort. The model comes with a sturdy safety shield that protects operators from flying debris during operation. Additionally, the cutter features a tough, welded frame construction, which enhances its durability and ensures that it can withstand the rigors of repeated use.

Another notable technology incorporated into the Bush Hog 2165 is its adjustable cutting height feature. This allows users to set the desired grass height easily, ranging from 1 to 4 inches. This flexibility is crucial for achieving the perfect lawn look and accommodating different mowing requirements throughout the seasons.

The 2165 also includes high-capacity cutting blades designed to provide a clean and consistent cut. The blades can be replaced or sharpened easily, further enhancing the cutter's practicality and extending its lifespan. Furthermore, the model is compatible with a variety of tractors, making it a versatile attachment that fits seamlessly into many existing agricultural setups.

Overall, the Bush Hog 2165 rotary cutter is engineered for reliability and performance. Its blend of advanced technologies, safety features, and user-friendly design make it an excellent choice for anyone in need of a dependable mowing solution. Whether for personal gardening projects or professional landscape management, the Bush Hog 2165 excels in meeting the demands of diverse applications, ensuring users achieve their landscaping goals efficiently and effectively.
Top Page Image Contents