Bush Hog 2165 manual PTO Pump Kits Optional, Assembly

Page 32

Figure 17

Upper Bar

Upper Brace

Tractor Upper Link Bracket

Link Weldment

Tractor Lower Link

Backhoe Mainframe

C

PTO PUMP KITS (Optional)

General Description

The PTO Pump Kits consist of those parts required to power the backhoe from the tractor’s PTO shaft. They include the PTO pump (6 or 8 gpm) and adapter, reservoir, filtration system, hydraulic hoses, and fittings. In addition, they include a torque plate that straddles the tractor’s draw bar and keeps the pump from turning with the PTO shaft.

NOTE - The speed of backhoe operations increases as PTO speed increases.

ASSEMBLY

IMPORTANT - When installing fittings, always use a paste-type thread sealant on perrmanent connections such as NPT (pipe) threads. DO NOT use Teflon tape as thread sealant. DO NOT use thread sealant on union ends of adapters. DO NOT over-tighten fittings - they can split or expand causing hydraulic fluid leakage.

Please refer to Figure 18 as a guide for assembly of the PTO Pump Kits.

1.Assemble reservoir (16) to backhoe using 3/8” x 1” bolts (2), flat washers (5), lock washers (7), and hex nuts (10).

2.Assemble 1” street elbow (34) to fill port on top of reservoir, orienting elbow so that it faces right rear of backhoe. Connect fill tube (17) to street elbow.

Elbow may have to be rotated slightly to allow fill tube to be installed so that its open end is located just behind foot platform to right of operator’s seat tower. Install breather cap with dipstick (18) onto fill tube.

3.If filter element (35) is not already attached to filter base, apply a thin layer of hydraulic fluid to the rub- ber seal on the filter element and then screw it onto the filter base. Hand tighten the element until it just seats on the filter base, then tighten an additional 3/4 of a turn. Use this same procedure when replac- ing filter element.

NOTE - Change filter element every time oil is changed.

4.Assemble 90° adapter fitting (27) to inlet port of fil- ter base and orient so that free end of fitting will point towards backhoe and angled slightly down- ward from horizontal. Assemble small 90° beaded tube fitting (26) to outlet port of filter base and orient so that free end of fitting will point towards backhoe and angled about 30° upward from horizontal. Connect filter assembly (15) to left rear corner of backhoe foot platform using 1/4” x 3/4” bolts (1), flat washers (4), and lock washers (6) - flow direction arrow on filter base should point toward rear of back- hoe. DO NOT over-tighten bolts as this will strip the threads on filter base.

5.Assemble on 90° JIC adapter fitting (28) to “Out/Return” port of bulkhead connection and an

30

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Backhoes Congratulations Table of Contents BackhoesThis Limited Warranty Shall not Apply Disclaimer of Implied Warranties & Consequential DamagesDealer Preparation Check List 2165, 2175, 2185 and 2195 BackhoesSafety Alert Symbol Your Safety is InvolvedBackhoe Important Safety PrecautionsTractor Avoid HIGH-PRESSURE Fluids Adjustments and InspectionTransportation EMPLOYERS, Employees and Operations Employee Tractor Operating InstructionsThis Act Seeks Osha RegulationsControls Keep bystanders a safe distance awayEngine Speed Lock Pins Storage Tubes Operating the BackhoeTransporting the Backhoe 50102295When Transporting Placing the StabilizersFilling the Bucket Dumping the BucketSide Slope Excavating or Trenching MiscellaneousFinishing Straight Walls BackfillingService Beginning of SeasonBleeding Backhoe Hydraulic System Hydraulic System HosesTooth Replacement LubricationTightening Nuts and Bolts On Models 2165, 2175, 2185 and 2195 the followInstall the swing safety lock pin as shown in Figures 1 Removal from Tractor StorageTroubleshooting Procedures Stabilizer PadsTroubleshooting Troubleshooting Load drops or settles Troubleshooting Troubleshooting Replacing Spool Seals Valve RepairReplace Center Section Assemblies Assembly GeneralGeneral Description Mounting Backhoe to Tractor or Skid Steer loadersAg Tractor using 3-point hitch Point Hitch Linkage 2165Assembly Refer to Figures 14 2185/2195 Point Hitch LinkageAssembly Assembly PTO Pump Kits OptionalHydraulic HOOK-UP to Tractor Do not Remove Tractor PTO GuardPage Closed Center System Hook-Up Diagram Hydraulic Hook-Up 2175, 2185Hook-Up Requirements Backhoe OperationTractor Preparation Power Beyond KitsFor Tractors with OPEN-CENTER Hydraulic Systems Great Bend Backhoe & Great Bend Loader Valve Second Procedure AssemblyFlow Divider KIT Optional General DescriptionFlow Divider Valve to Backhoe Mounting Tractors with an auxiliary hydraulic flow of 15 gpm or lessTesting Backhoe Hydraulic Hook-Up For Tractor Hydraulic Flow Greater than 15 GPMFlow Divider Valve to Skid Steer Adapter Mounting For Skid Steer H Ydraulic Flow of 15 GPM or Less For Skid Steer HydraulicSeries Page Safety Decals Torque Specifications Recommended Torque in Foot Pounds Newton MetersBox 1039 Selma, AL 334

2165 specifications

The Bush Hog 2165 is a versatile and robust rotary cutter designed for heavy-duty lawn care and land management applications. This model is a part of the renowned Bush Hog lineup, known for its durability, efficiency, and ease of use. The 2165 strikes an excellent balance between performance and functionality, making it an ideal choice for homeowners, landscapers, and farmers alike.

One of the standout features of the Bush Hog 2165 is its impressive cutting width of 65 inches, which allows it to cover large areas quickly and effectively. This makes it particularly suitable for tackling overgrown fields, pastures, and roadside maintenance tasks. The cutter is equipped with a powerful, heavy-duty gearbox that ensures reliable performance under various conditions, providing users with the confidence to handle even the most challenging cutting jobs.

The design of the Bush Hog 2165 emphasizes user safety and comfort. The model comes with a sturdy safety shield that protects operators from flying debris during operation. Additionally, the cutter features a tough, welded frame construction, which enhances its durability and ensures that it can withstand the rigors of repeated use.

Another notable technology incorporated into the Bush Hog 2165 is its adjustable cutting height feature. This allows users to set the desired grass height easily, ranging from 1 to 4 inches. This flexibility is crucial for achieving the perfect lawn look and accommodating different mowing requirements throughout the seasons.

The 2165 also includes high-capacity cutting blades designed to provide a clean and consistent cut. The blades can be replaced or sharpened easily, further enhancing the cutter's practicality and extending its lifespan. Furthermore, the model is compatible with a variety of tractors, making it a versatile attachment that fits seamlessly into many existing agricultural setups.

Overall, the Bush Hog 2165 rotary cutter is engineered for reliability and performance. Its blend of advanced technologies, safety features, and user-friendly design make it an excellent choice for anyone in need of a dependable mowing solution. Whether for personal gardening projects or professional landscape management, the Bush Hog 2165 excels in meeting the demands of diverse applications, ensuring users achieve their landscaping goals efficiently and effectively.
Top Page Image Contents