Bush Hog 2165 manual General Description, Mounting Backhoe to Tractor or Skid Steer loaders

Page 27

3.Remove parts bag containing bucket pins from backhoe. Attach bucket (D) to dipperstick (B) using one pin, 3/8” bolt, and locknut.

4.Attach bucket link (E) to bucket, using same hard- ware as listed for step #3.

5.Reposition hoist on backhoe to prevent tipping and raise mainframe (G) slightly. Remove all remaining strapping and attach stabilizers (F) to mainframe (G) using pins and hardware from parts bag.

6.Attach stabilizer cylinders (H) to stabilizers (F) using pins and hardware from parts bag.

7.Using caution to prevent tipping, raise mainframe

(G) with hoist to a height of approximately 17” and remove skid. Block mainframe (G) and swing frame (J) securely.

8.Follow the Attaching Kit Assembly Instructions to mount the backhoe to the tractor. Check the installa- tion carefully and make sure that all members are cor- rectly installed and securely fastened.

Assembly: (2165 & 2175) -Figure12

(See “General” note, page 24)

IMPORTANT: Tighten all hardware to torque requirements specified in torque chart on page 45.

CAUTION

DO NOT cut any strapping that fastens the back- hoe mainframe and swing frame to the skid at this time.

1.Remove the stabilizer assemblies and any miscella- neous items which have been fastened to skid and arrange conveniently. Be sure hoses to stabilizer cylin- ders are routed above the cylinder-to-mainframe pivot pin connection.

2.Support boom (A) and dipperstick (B) with hoist attached at (C) and remove boom transport lock pin. Lower boom and extend dipperstick until end of dip- perstick is approximately 16” above the ground. Move control handles to “BOOM DOWN” position and “CROWD OUT” position as required to aid move- ment.

CAUTION

Be sure hoist being used is suitable, has suffi- cient capacity, and is in the proper position. Do not allow anyone under a backhoe member sup- ported by hoist.

3.Remove parts bag containing bucket pins from backhoe. Attach bucket (D) to dipperstick (B) using one pin, 3/8” bolt, and locknut.

4.Attach bucket link (E) to bucket, using same hard- ware as listed for step #3.

5.Reposition hoist on backhoe to prevent tipping and raise mainframe (G) slightly. Remove all remaining strapping and crate base. Using caution to prevent tipping, raise mainframe (G) to approximately 13” and block mainframe and swing frame (J) securely.

6.Attach stabilizers (F) to mainframe (G) using pins and hardware from parts bag.

7.Attach stabilizer cylinders (H) to stabilizers (F) using pins and hardware from parts bag.

8.Follow the Attaching Kit Assembly Instructions to mount the backhoe to the tractor. Check the installa- tion carefully and make sure that all members are cor-

MOUNTING KITS AND OPTIONAL KITS ASSEMBLY

3- POINT HITCH LINKAGE (For 2165 & 2175)

General Description

Mounting and hydraulic kits do not include hoses to connect the backhoe to the tractor hydraulic system. Additional hydraulic components, hoses, and/or kits will be required to complete the hook-up to the tractor hydraulic system. Refer to the “Hydraulic Hook-up” section for further information. PTO pump kits are available as options.

Mounting Backhoe to Tractor or Skid Steer loaders

The Bush Hog backhoe can be mounted to the power source using three different attaching kits.

1.To an agricultural tractor’s 3-point hitch linkage using the 3-point hitch kit. The 3-point hitch kit is the

same regardless of tractor model and the instructions for attaching the kit to the backhoe are included below. See Figure 13 for general appearance.

2.To an agricultural tractor using a subframe kit specifically offered for the tractor model and backhoe being mounted: The subframe kit instructions differ with each tractor/backhoe combination and come included with the individual subframe kit.

3.To a skid steer loader using a skid steer adaptor kit offered for the skid steer model and backhoe series being mounted. The skid steer adapter kit instructions differ with each skid steer model/backhoe combina- tion and come included with the individual skid steer adapter kit.

25

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Backhoes Congratulations Backhoes Table of ContentsDisclaimer of Implied Warranties & Consequential Damages This Limited Warranty Shall not Apply2165, 2175, 2185 and 2195 Backhoes Dealer Preparation Check ListYour Safety is Involved Safety Alert SymbolImportant Safety Precautions TractorBackhoe Adjustments and Inspection TransportationAvoid HIGH-PRESSURE Fluids Osha Regulations EMPLOYERS, Employees and OperationsEmployee Tractor Operating Instructions This Act SeeksKeep bystanders a safe distance away Engine SpeedControls Operating the Backhoe Lock Pins Storage Tubes50102295 Transporting the BackhoePlacing the Stabilizers When TransportingDumping the Bucket Filling the BucketBackfilling Side Slope Excavating or TrenchingMiscellaneous Finishing Straight WallsHydraulic System Hoses ServiceBeginning of Season Bleeding Backhoe Hydraulic SystemOn Models 2165, 2175, 2185 and 2195 the follow Tooth ReplacementLubrication Tightening Nuts and BoltsRemoval from Tractor Storage Install the swing safety lock pin as shown in Figures 1Stabilizer Pads Troubleshooting ProceduresTroubleshooting Troubleshooting Load drops or settles Troubleshooting Troubleshooting Valve Repair Replace Center Section AssembliesReplacing Spool Seals General AssemblyMounting Backhoe to Tractor or Skid Steer loaders General DescriptionPoint Hitch Linkage 2165 Ag Tractor using 3-point hitchAssembly Refer to Figures 14 Point Hitch Linkage 2185/2195Assembly PTO Pump Kits Optional AssemblyDo not Remove Tractor PTO Guard Hydraulic HOOK-UP to TractorPage Closed Center System Backhoe Operation Hook-Up DiagramHydraulic Hook-Up 2175, 2185 Hook-Up RequirementsPower Beyond Kits For Tractors with OPEN-CENTER Hydraulic SystemsTractor Preparation Great Bend Backhoe & Great Bend Loader Valve Assembly Second ProcedureTractors with an auxiliary hydraulic flow of 15 gpm or less Flow Divider KIT OptionalGeneral Description Flow Divider Valve to Backhoe MountingFor Tractor Hydraulic Flow Greater than 15 GPM Testing Backhoe Hydraulic Hook-UpFlow Divider Valve to Skid Steer Adapter Mounting For Skid Steer Hydraulic For Skid Steer H Ydraulic Flow of 15 GPM or LessSeries Page Safety Decals Recommended Torque in Foot Pounds Newton Meters Torque SpecificationsBox 1039 Selma, AL 334

2165 specifications

The Bush Hog 2165 is a versatile and robust rotary cutter designed for heavy-duty lawn care and land management applications. This model is a part of the renowned Bush Hog lineup, known for its durability, efficiency, and ease of use. The 2165 strikes an excellent balance between performance and functionality, making it an ideal choice for homeowners, landscapers, and farmers alike.

One of the standout features of the Bush Hog 2165 is its impressive cutting width of 65 inches, which allows it to cover large areas quickly and effectively. This makes it particularly suitable for tackling overgrown fields, pastures, and roadside maintenance tasks. The cutter is equipped with a powerful, heavy-duty gearbox that ensures reliable performance under various conditions, providing users with the confidence to handle even the most challenging cutting jobs.

The design of the Bush Hog 2165 emphasizes user safety and comfort. The model comes with a sturdy safety shield that protects operators from flying debris during operation. Additionally, the cutter features a tough, welded frame construction, which enhances its durability and ensures that it can withstand the rigors of repeated use.

Another notable technology incorporated into the Bush Hog 2165 is its adjustable cutting height feature. This allows users to set the desired grass height easily, ranging from 1 to 4 inches. This flexibility is crucial for achieving the perfect lawn look and accommodating different mowing requirements throughout the seasons.

The 2165 also includes high-capacity cutting blades designed to provide a clean and consistent cut. The blades can be replaced or sharpened easily, further enhancing the cutter's practicality and extending its lifespan. Furthermore, the model is compatible with a variety of tractors, making it a versatile attachment that fits seamlessly into many existing agricultural setups.

Overall, the Bush Hog 2165 rotary cutter is engineered for reliability and performance. Its blend of advanced technologies, safety features, and user-friendly design make it an excellent choice for anyone in need of a dependable mowing solution. Whether for personal gardening projects or professional landscape management, the Bush Hog 2165 excels in meeting the demands of diverse applications, ensuring users achieve their landscaping goals efficiently and effectively.
Top Page Image Contents