Bush Hog 2165 manual Troubleshooting

Page 21

Troubleshooting (Continued)

Problem

Cause

Correction

Loss of power in any one

Worn or damaged rod seals on

Repack cylinder. Rebuild cylinder,

cylinder, including lift

cylinder; external leaks

replacing damaged parts as necessary.

and crowd

 

 

Spool not moved to full stroke

Check spool travel - should be .26”

 

 

 

either way, or a total of .52”.

 

Overload relief valve in the control

Clean relief carefully but do not disturb

 

valve stuck open or malfunctioning

its pressure setting as it cannot be field

 

 

calibrated, or replace cartridge.

 

Worn control valve

Replace the control valve.

 

 

 

Loss of power in swing

Loose oil line connections,

Tighten all hose connections and

cylinders, but other

leaks in line or broken lines

replace any damaged O-rings at

cylinders functioning

 

leaking O-ring fittings. Check and

properly.

 

replace any damaged hoses and lines.

 

 

 

 

Restrictions in oil lines

Check and replace any damaged hoses

 

 

and lines. Check for pinched hoses.

 

Oil is bypassing cylinder piston,

Replace or rebuild the cylinder; replace

 

scored piston, worn piston

damaged parts.

 

packing, or defective piston

 

 

assembly

 

 

Scored piston rods and worn

Replace or rebuild the cylinder; replace

 

guides in cylinder

damaged parts.

 

 

 

 

Bent piston rod in cylinder

Replace or rebuild the cylinder; replace

 

 

damaged parts.

 

Worn or damaged rod seals on

Repack cylinder. Rebuild cylinder,

 

cylinder; external leaks

replacing damaged parts as necessary.

 

 

 

 

Spool not moved to full stroke

Check spool travel - should be .26”

 

 

either way, or a total of .52”.

 

 

 

 

Relief valve setting in backhoe

Relief pressure will have to be checked

 

control valve too low or defective

and corrections made. Backhoe

 

 

system pressure is 2400 PSI. Relief

 

 

valve may need cleaning and over

 

 

hauling, or entire cartridge must be

 

 

replaced.

 

 

 

 

Worn control valve

Replace the control valve.

 

 

 

Maximum swing action

Bent piston rod in cylinder

Replace or rebuild the cylinder; replace

cannot be obtained

 

damaged parts.

 

Something jamming the swing

Remove interference.

 

linkage

 

 

 

 

Slow operation of machine

 

 

(lack of power) all cylinders

Low oil supply in reservoir

Fill to proper level.

 

 

 

 

Oil viscosity too heavy, or oil

Use recommended hydraulic fluid. Run

 

is not at operating temperature

machine until oil reaches operating

 

 

temperature.

 

Insufficient pumping

Advance engine throttle.

 

 

 

 

Diverter valve on prime mover

Diverter valve may need rebuilding or

 

leaking externally or bypassing

replacing.

 

oil internally through valve to

 

 

reservoir

 

 

Excessive back pressure

Relieve condition. Restriction may be

 

 

from outlet to reservoir.

19

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Backhoes Congratulations Backhoes Table of ContentsDisclaimer of Implied Warranties & Consequential Damages This Limited Warranty Shall not Apply2165, 2175, 2185 and 2195 Backhoes Dealer Preparation Check ListYour Safety is Involved Safety Alert SymbolImportant Safety Precautions TractorBackhoe Adjustments and Inspection TransportationAvoid HIGH-PRESSURE Fluids Employee Tractor Operating Instructions EMPLOYERS, Employees and OperationsThis Act Seeks Osha RegulationsKeep bystanders a safe distance away Engine SpeedControls Operating the Backhoe Lock Pins Storage Tubes50102295 Transporting the BackhoePlacing the Stabilizers When TransportingDumping the Bucket Filling the BucketMiscellaneous Side Slope Excavating or TrenchingFinishing Straight Walls BackfillingBeginning of Season ServiceBleeding Backhoe Hydraulic System Hydraulic System HosesLubrication Tooth ReplacementTightening Nuts and Bolts On Models 2165, 2175, 2185 and 2195 the followRemoval from Tractor Storage Install the swing safety lock pin as shown in Figures 1Stabilizer Pads Troubleshooting ProceduresTroubleshooting Troubleshooting Load drops or settles Troubleshooting Troubleshooting Valve Repair Replace Center Section AssembliesReplacing Spool Seals General AssemblyMounting Backhoe to Tractor or Skid Steer loaders General DescriptionPoint Hitch Linkage 2165 Ag Tractor using 3-point hitchAssembly Refer to Figures 14 Point Hitch Linkage 2185/2195Assembly PTO Pump Kits Optional AssemblyDo not Remove Tractor PTO Guard Hydraulic HOOK-UP to TractorPage Closed Center System Hydraulic Hook-Up 2175, 2185 Hook-Up DiagramHook-Up Requirements Backhoe OperationPower Beyond Kits For Tractors with OPEN-CENTER Hydraulic SystemsTractor Preparation Great Bend Backhoe & Great Bend Loader Valve Assembly Second ProcedureGeneral Description Flow Divider KIT OptionalFlow Divider Valve to Backhoe Mounting Tractors with an auxiliary hydraulic flow of 15 gpm or lessFor Tractor Hydraulic Flow Greater than 15 GPM Testing Backhoe Hydraulic Hook-UpFlow Divider Valve to Skid Steer Adapter Mounting For Skid Steer Hydraulic For Skid Steer H Ydraulic Flow of 15 GPM or LessSeries Page Safety Decals Recommended Torque in Foot Pounds Newton Meters Torque SpecificationsBox 1039 Selma, AL 334

2165 specifications

The Bush Hog 2165 is a versatile and robust rotary cutter designed for heavy-duty lawn care and land management applications. This model is a part of the renowned Bush Hog lineup, known for its durability, efficiency, and ease of use. The 2165 strikes an excellent balance between performance and functionality, making it an ideal choice for homeowners, landscapers, and farmers alike.

One of the standout features of the Bush Hog 2165 is its impressive cutting width of 65 inches, which allows it to cover large areas quickly and effectively. This makes it particularly suitable for tackling overgrown fields, pastures, and roadside maintenance tasks. The cutter is equipped with a powerful, heavy-duty gearbox that ensures reliable performance under various conditions, providing users with the confidence to handle even the most challenging cutting jobs.

The design of the Bush Hog 2165 emphasizes user safety and comfort. The model comes with a sturdy safety shield that protects operators from flying debris during operation. Additionally, the cutter features a tough, welded frame construction, which enhances its durability and ensures that it can withstand the rigors of repeated use.

Another notable technology incorporated into the Bush Hog 2165 is its adjustable cutting height feature. This allows users to set the desired grass height easily, ranging from 1 to 4 inches. This flexibility is crucial for achieving the perfect lawn look and accommodating different mowing requirements throughout the seasons.

The 2165 also includes high-capacity cutting blades designed to provide a clean and consistent cut. The blades can be replaced or sharpened easily, further enhancing the cutter's practicality and extending its lifespan. Furthermore, the model is compatible with a variety of tractors, making it a versatile attachment that fits seamlessly into many existing agricultural setups.

Overall, the Bush Hog 2165 rotary cutter is engineered for reliability and performance. Its blend of advanced technologies, safety features, and user-friendly design make it an excellent choice for anyone in need of a dependable mowing solution. Whether for personal gardening projects or professional landscape management, the Bush Hog 2165 excels in meeting the demands of diverse applications, ensuring users achieve their landscaping goals efficiently and effectively.
Top Page Image Contents