Bush Hog 2165 manual Second Procedure, Assembly

Page 39

-

SECOND PROCEDURE

ASSEMBLY OF A GREAT BEND BACKHOE TO A NON GREAT BEND LOADER VALVE - OR - GREAT BEND BACKHOE TO LOADER VALVE USING PTO PUMP KIT OPTION

Assembly of a Great Bend backhoe to a non-Great Bend loader valve, OR a Great Bend Backhoe to a loader valve using the PTO Pump Kit option.

IMPORTANT:

●Improper hydraulic hook-up can cause seri- ous damage to the backhoe control valve, loader valve, tractor valve, and other hydraulic components.

●The pressure supply line from the PTO pump must be connected to the pressure inlet port on the backhoe bulkhead connection whether using a Great Bend loader valve or a non- Great Bend loader valve. Never connect the pressure supply line from the PTO pump to the loader valve pressure inlet port because excessive pressure will build up resulting in damage to the PTO pump.

The following instructions are to be used to connect the backhoe valve in line with a loader valve that is not a Great Bend loader valve. When connecting the Great Bend backhoe valve to a loader valve other than one obtained from Great Bend, the input pres- sure line from the tractor will be connected to the pressure port on the backhoe bulkhead connection first. In order to properly plumb the system, the back- hoe valve will require converting to a power beyond valve. The power beyond pressure line from the backhoe valve will be connected to the input pres-

sure port of the loader valve. The power beyond kit for the backhoe being assembled must be ordered as a separate item from Great Bend.

Assembly

1.Remove the front cover that encloses the back- hoe valve within the control console.

2.Carefully clean the top and front sides of the backhoe valve and remove the large “Port C” plug located on the front of the right hand end section of the valve.

3.Install power beyond / closed center plug inside of port. Make sure power beyond / closed center plug is tightly engaged.

4.Install 90° male adapter into “C” port with open end of adapter (JIC side) oriented so that it points down and towards the right side of the backhoe.

5.Connect hydraulic hose (supplied by customer) to 90° male adapter. The hydraulic hose should have the same pressure rating as the original pressure hose to the loader or other accessory valve.

6.Connect the other end of the hydraulic hose to the pressure port of the loader or accessory valve using fittings (supplied by customer) as required. Refer to Figure 24.

7.Complete assembly of the backhoe “pressure” and “return” hydraulic hoses and a tee fitting (all sup- plied by customer) as shown.

8.Complete assembly of the loader or accessory valve “return” hydraulic hose (supplied by cus- tomer) to the tee fitting as shown.

Figure 24

To Tractor Reservoir

Loader Or

Inlet

 

 

Port or Backhoe

Accessory Valve

 

Return Filter Inlet

Remove port “C” plug and install closed center plug inside port.

Backhoe Valve

Return From

Backhoe Valve

Pressure

Pressure To

Backhoe Valve

Outlet

Return From

Loader Valve

Pressure To

Loader Valve

Backhoe Bulkhead

ConnectorFrom Tractor Pressure “Out” Port Or Outlet Port

Of PTO Pump

37

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Backhoes Congratulations Backhoes Table of ContentsDisclaimer of Implied Warranties & Consequential Damages This Limited Warranty Shall not Apply2165, 2175, 2185 and 2195 Backhoes Dealer Preparation Check ListYour Safety is Involved Safety Alert SymbolImportant Safety Precautions TractorBackhoe Adjustments and Inspection TransportationAvoid HIGH-PRESSURE Fluids Osha Regulations EMPLOYERS, Employees and OperationsEmployee Tractor Operating Instructions This Act SeeksKeep bystanders a safe distance away Engine SpeedControls Operating the Backhoe Lock Pins Storage Tubes50102295 Transporting the BackhoePlacing the Stabilizers When TransportingDumping the Bucket Filling the BucketBackfilling Side Slope Excavating or TrenchingMiscellaneous Finishing Straight WallsHydraulic System Hoses ServiceBeginning of Season Bleeding Backhoe Hydraulic SystemOn Models 2165, 2175, 2185 and 2195 the follow Tooth ReplacementLubrication Tightening Nuts and BoltsRemoval from Tractor Storage Install the swing safety lock pin as shown in Figures 1Stabilizer Pads Troubleshooting ProceduresTroubleshooting Troubleshooting Load drops or settles Troubleshooting Troubleshooting Valve Repair Replace Center Section AssembliesReplacing Spool Seals General AssemblyMounting Backhoe to Tractor or Skid Steer loaders General DescriptionPoint Hitch Linkage 2165 Ag Tractor using 3-point hitchAssembly Refer to Figures 14 Point Hitch Linkage 2185/2195Assembly PTO Pump Kits Optional AssemblyDo not Remove Tractor PTO Guard Hydraulic HOOK-UP to TractorPage Closed Center System Backhoe Operation Hook-Up DiagramHydraulic Hook-Up 2175, 2185 Hook-Up RequirementsPower Beyond Kits For Tractors with OPEN-CENTER Hydraulic SystemsTractor Preparation Great Bend Backhoe & Great Bend Loader Valve Assembly Second ProcedureTractors with an auxiliary hydraulic flow of 15 gpm or less Flow Divider KIT OptionalGeneral Description Flow Divider Valve to Backhoe MountingFor Tractor Hydraulic Flow Greater than 15 GPM Testing Backhoe Hydraulic Hook-UpFlow Divider Valve to Skid Steer Adapter Mounting For Skid Steer Hydraulic For Skid Steer H Ydraulic Flow of 15 GPM or LessSeries Page Safety Decals Recommended Torque in Foot Pounds Newton Meters Torque SpecificationsBox 1039 Selma, AL 334

2165 specifications

The Bush Hog 2165 is a versatile and robust rotary cutter designed for heavy-duty lawn care and land management applications. This model is a part of the renowned Bush Hog lineup, known for its durability, efficiency, and ease of use. The 2165 strikes an excellent balance between performance and functionality, making it an ideal choice for homeowners, landscapers, and farmers alike.

One of the standout features of the Bush Hog 2165 is its impressive cutting width of 65 inches, which allows it to cover large areas quickly and effectively. This makes it particularly suitable for tackling overgrown fields, pastures, and roadside maintenance tasks. The cutter is equipped with a powerful, heavy-duty gearbox that ensures reliable performance under various conditions, providing users with the confidence to handle even the most challenging cutting jobs.

The design of the Bush Hog 2165 emphasizes user safety and comfort. The model comes with a sturdy safety shield that protects operators from flying debris during operation. Additionally, the cutter features a tough, welded frame construction, which enhances its durability and ensures that it can withstand the rigors of repeated use.

Another notable technology incorporated into the Bush Hog 2165 is its adjustable cutting height feature. This allows users to set the desired grass height easily, ranging from 1 to 4 inches. This flexibility is crucial for achieving the perfect lawn look and accommodating different mowing requirements throughout the seasons.

The 2165 also includes high-capacity cutting blades designed to provide a clean and consistent cut. The blades can be replaced or sharpened easily, further enhancing the cutter's practicality and extending its lifespan. Furthermore, the model is compatible with a variety of tractors, making it a versatile attachment that fits seamlessly into many existing agricultural setups.

Overall, the Bush Hog 2165 rotary cutter is engineered for reliability and performance. Its blend of advanced technologies, safety features, and user-friendly design make it an excellent choice for anyone in need of a dependable mowing solution. Whether for personal gardening projects or professional landscape management, the Bush Hog 2165 excels in meeting the demands of diverse applications, ensuring users achieve their landscaping goals efficiently and effectively.
Top Page Image Contents