Bush Hog 2165 manual Transportation, Adjustments and Inspection, Avoid HIGH-PRESSURE Fluids

Page 8

SAFETY PRECAUTIONS CONTINUED

12.DO NOT dig under stabilizers or tractor backhoe. Soft ground or sandy soil can cause cave-ins.

13.KEEP BUCKET away from the stabilizer area to avoid possible stabilizer damage.

14.ALWAYS swing bucket uphill to dump when on a hillside and keep loaded bucket low.

15.SET BRAKES and block wheels when operating on hills and banks to avoid dangerous runaway.

16.WATCH for overhead wires. DO NOT touch wires with any part of the backhoe.

17.NEVER allow a person to work under a raised bucket.

18.NEVER lift a person with the backhoe.

19.DO NOT use the backhoe as a battering ram. Use the backhoe only for digging.

20.ALWAYS lower the backhoe bucket and stabilizers to the ground, shut off engine, and apply the parking brake before getting off unit, or when not digging.

21.NEVER leave the tractor unattended with the engine running.

22.DO NOT attempt to raise the tractor off the ground or move the tractor forward or backward using the backhoe dipperstick or bucket.

TRANSPORTATION

1.ALWAYS engage safety locks before transporting backhoe. See Figures 1 & 3.

2.DO NOT drive the tractor near the edge of a ditch or excavation.

3.ALWAYS use accessory lights and devices when transporting on a road or highway to warn operators of other vehicles. Check your local government regulations.

4.BE SURE the SMV emblem is visible to the rear.

ADJUSTMENTS AND INSPECTION

1.CHECK pins that attach backhoe to tractor and all pivot pins for tightness several times daily. Replace any parts that are bent, broken or missing.

2.ALWAYS engage safety locks before servicing backhoe. See Figures 1 & 3.

3.DO NOT oil, grease, or adjust the backhoe while it is in motion. For greasing, see Service section for details.

4.DO NOT change any backhoe relief valve settings. They are factory set for best backhoe performance and safety.

5.PROTECT YOUR EYES - WEAR SAFETY GLASSES.

6.GUARD AGAINST INJURY when driving connecting pins or performing any repair in which particles can chip from work piece or striking tool.

7.DO NOT remove any guards on backhoe or tractor.

AVOID HIGH-PRESSURE FLUIDS

ESCAPING fluid under pressure can have sufficient force to penetrate the skin and cause serious injury. Be sure to stop engine and relieve all pressure before disconnecting lines. Be sure all connections are tight and that lines, pipes, and hoses are not damaged before applying pressure to the system. Fluid escaping from a very small hole can be almost invisible. Use a piece of cardboard or wood - not your hands-to search for suspected leaks.

SEE A DOCTOR at once if injured by escaping fluid. Serious infection or gan- grene can develop if proper medical treatment is not administered immediately.

6

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Backhoes Congratulations Table of Contents BackhoesThis Limited Warranty Shall not Apply Disclaimer of Implied Warranties & Consequential DamagesDealer Preparation Check List 2165, 2175, 2185 and 2195 BackhoesSafety Alert Symbol Your Safety is InvolvedBackhoe Important Safety PrecautionsTractor Avoid HIGH-PRESSURE Fluids Adjustments and InspectionTransportation EMPLOYERS, Employees and Operations Employee Tractor Operating InstructionsThis Act Seeks Osha RegulationsControls Keep bystanders a safe distance awayEngine Speed Lock Pins Storage Tubes Operating the BackhoeTransporting the Backhoe 50102295When Transporting Placing the StabilizersFilling the Bucket Dumping the BucketSide Slope Excavating or Trenching MiscellaneousFinishing Straight Walls BackfillingService Beginning of SeasonBleeding Backhoe Hydraulic System Hydraulic System HosesTooth Replacement LubricationTightening Nuts and Bolts On Models 2165, 2175, 2185 and 2195 the followInstall the swing safety lock pin as shown in Figures 1 Removal from Tractor StorageTroubleshooting Procedures Stabilizer PadsTroubleshooting Troubleshooting Load drops or settles Troubleshooting Troubleshooting Replacing Spool Seals Valve RepairReplace Center Section Assemblies Assembly GeneralGeneral Description Mounting Backhoe to Tractor or Skid Steer loadersAg Tractor using 3-point hitch Point Hitch Linkage 2165Assembly Refer to Figures 14 2185/2195 Point Hitch LinkageAssembly Assembly PTO Pump Kits OptionalHydraulic HOOK-UP to Tractor Do not Remove Tractor PTO GuardPage Closed Center System Hook-Up Diagram Hydraulic Hook-Up 2175, 2185Hook-Up Requirements Backhoe OperationTractor Preparation Power Beyond KitsFor Tractors with OPEN-CENTER Hydraulic Systems Great Bend Backhoe & Great Bend Loader Valve Second Procedure AssemblyFlow Divider KIT Optional General DescriptionFlow Divider Valve to Backhoe Mounting Tractors with an auxiliary hydraulic flow of 15 gpm or lessTesting Backhoe Hydraulic Hook-Up For Tractor Hydraulic Flow Greater than 15 GPMFlow Divider Valve to Skid Steer Adapter Mounting For Skid Steer H Ydraulic Flow of 15 GPM or Less For Skid Steer HydraulicSeries Page Safety Decals Torque Specifications Recommended Torque in Foot Pounds Newton MetersBox 1039 Selma, AL 334

2165 specifications

The Bush Hog 2165 is a versatile and robust rotary cutter designed for heavy-duty lawn care and land management applications. This model is a part of the renowned Bush Hog lineup, known for its durability, efficiency, and ease of use. The 2165 strikes an excellent balance between performance and functionality, making it an ideal choice for homeowners, landscapers, and farmers alike.

One of the standout features of the Bush Hog 2165 is its impressive cutting width of 65 inches, which allows it to cover large areas quickly and effectively. This makes it particularly suitable for tackling overgrown fields, pastures, and roadside maintenance tasks. The cutter is equipped with a powerful, heavy-duty gearbox that ensures reliable performance under various conditions, providing users with the confidence to handle even the most challenging cutting jobs.

The design of the Bush Hog 2165 emphasizes user safety and comfort. The model comes with a sturdy safety shield that protects operators from flying debris during operation. Additionally, the cutter features a tough, welded frame construction, which enhances its durability and ensures that it can withstand the rigors of repeated use.

Another notable technology incorporated into the Bush Hog 2165 is its adjustable cutting height feature. This allows users to set the desired grass height easily, ranging from 1 to 4 inches. This flexibility is crucial for achieving the perfect lawn look and accommodating different mowing requirements throughout the seasons.

The 2165 also includes high-capacity cutting blades designed to provide a clean and consistent cut. The blades can be replaced or sharpened easily, further enhancing the cutter's practicality and extending its lifespan. Furthermore, the model is compatible with a variety of tractors, making it a versatile attachment that fits seamlessly into many existing agricultural setups.

Overall, the Bush Hog 2165 rotary cutter is engineered for reliability and performance. Its blend of advanced technologies, safety features, and user-friendly design make it an excellent choice for anyone in need of a dependable mowing solution. Whether for personal gardening projects or professional landscape management, the Bush Hog 2165 excels in meeting the demands of diverse applications, ensuring users achieve their landscaping goals efficiently and effectively.
Top Page Image Contents