Bush Hog 2165 manual Transporting the Backhoe, 50102295

Page 12

Location: Back Of Control Panel

It is not difficult to become an efficient operator. Control lever operating decal is located on back of the control console. Study this decal. It will assist you in becoming familiar with the controls.

Smooth, light handling of the controls will result in the most efficient backhoe operation.

Operate the backhoe control levers to become famil- iar with their speed and movements. The engine speed and the size of the hydraulic system will deter- mine the speed of cylinder operation. When powering from tractor systems with higher output than required, reduce engine RPM to obtain acceptable backhoe operating speed. If backhoe is to be mounted to a tractor or to a skid steer loader with a hydraulic flow rate exceeding 12 gallons per minute (gpm), then the backhoe must be equipped with a Flow Divider Kit. Refer to “Flow Divider Kit” section of this manual for assembly and installation instructions.

Swing the boom several times to practice controlling the speed of swing. Do not operate the swing more than 45° each way for the first few times, then gradu- ally increase the arc.

IMPORTANT: To avoid damage to the backhoe, do not slam unit into the rubber bumpers when swinging the boom right or left.

The boom “float” function may be used during digging to eliminate down pressure when cleaning the bottom of a trench. The primary purpose of the boom “float” function is to protect the operator from serious injury in the event that the backhoe or tractor hitch would fail.

Best results are obtained by digging near the center of the swing arc so material can be dumped on either side.

As the operator becomes more familiar with the oper- ation of the backhoe, it will be common practice to operate two controls at one time. For example, with the bucket extended and the dipperstick extended, the lift control and crowd control can be operated together to bring the bucket toward the operator with down pressure on it. As the dipperstick approaches the operator, the crowd and bucket controls can be operated to close the bucket and trap the material. At the end of the stroke, the lift and crowd controls are operated to move the load up and away from the

operator to save time in clearing the excavation.

This dual operation of controls will speed and simplify the digging operation. Normally the two or more movements will not be equal or even simultaneous, but as the pressure within the cylinders changes, and the resistance on an operating member of the hoe lessens, it will begin to move. It is balancing the force of one member against the other.

NOTE: Actuating the bucket is the key to powerful dig- ging. Operating the crowd and bucket controls simul- taneously will insure a full bucket and prevent waste motion and time.

TRANSPORTING THE BACKHOE

IMPORTANT: To prevent serious damage to the tractor, read and follow the instructions on the fol- lowing decal:

IMPORTANT

IMPROPER TRANSPORTING

METHODS CAN CAUSE SER-

IOUS DAMAGE TO TRACTOR.

•ENGAGE BOTH SAFETY LOCKS WHEN TRANSPORTING BACKHOE.

•TRAVEL SLOWLY OVER ROUGH TERRAIN.

•WHEN TRANSPORTING ON TRUCK OR TRAILER, LOWER BACKHOE BOOM SO BUCKET RESTS FIRMLY ON BED. APPLY RESTRAINTS TO TRACTOR, NOT TO BACKHOE OR BACKHOE ATTACHING KIT.

50102295

Location: Right Side of Boom

10

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Backhoes Congratulations Table of Contents BackhoesThis Limited Warranty Shall not Apply Disclaimer of Implied Warranties & Consequential DamagesDealer Preparation Check List 2165, 2175, 2185 and 2195 BackhoesSafety Alert Symbol Your Safety is InvolvedImportant Safety Precautions TractorBackhoe Adjustments and Inspection TransportationAvoid HIGH-PRESSURE Fluids EMPLOYERS, Employees and Operations Employee Tractor Operating InstructionsThis Act Seeks Osha RegulationsKeep bystanders a safe distance away Engine SpeedControls Lock Pins Storage Tubes Operating the BackhoeTransporting the Backhoe 50102295When Transporting Placing the StabilizersFilling the Bucket Dumping the BucketSide Slope Excavating or Trenching MiscellaneousFinishing Straight Walls BackfillingService Beginning of SeasonBleeding Backhoe Hydraulic System Hydraulic System HosesTooth Replacement LubricationTightening Nuts and Bolts On Models 2165, 2175, 2185 and 2195 the followInstall the swing safety lock pin as shown in Figures 1 Removal from Tractor StorageTroubleshooting Procedures Stabilizer PadsTroubleshooting Troubleshooting Load drops or settles Troubleshooting Troubleshooting Valve Repair Replace Center Section AssembliesReplacing Spool Seals Assembly GeneralGeneral Description Mounting Backhoe to Tractor or Skid Steer loadersAg Tractor using 3-point hitch Point Hitch Linkage 2165Assembly Refer to Figures 14 2185/2195 Point Hitch LinkageAssembly Assembly PTO Pump Kits OptionalHydraulic HOOK-UP to Tractor Do not Remove Tractor PTO GuardPage Closed Center System Hook-Up Diagram Hydraulic Hook-Up 2175, 2185Hook-Up Requirements Backhoe OperationPower Beyond Kits For Tractors with OPEN-CENTER Hydraulic SystemsTractor Preparation Great Bend Backhoe & Great Bend Loader Valve Second Procedure AssemblyFlow Divider KIT Optional General DescriptionFlow Divider Valve to Backhoe Mounting Tractors with an auxiliary hydraulic flow of 15 gpm or lessTesting Backhoe Hydraulic Hook-Up For Tractor Hydraulic Flow Greater than 15 GPMFlow Divider Valve to Skid Steer Adapter Mounting For Skid Steer H Ydraulic Flow of 15 GPM or Less For Skid Steer HydraulicSeries Page Safety Decals Torque Specifications Recommended Torque in Foot Pounds Newton MetersBox 1039 Selma, AL 334

2165 specifications

The Bush Hog 2165 is a versatile and robust rotary cutter designed for heavy-duty lawn care and land management applications. This model is a part of the renowned Bush Hog lineup, known for its durability, efficiency, and ease of use. The 2165 strikes an excellent balance between performance and functionality, making it an ideal choice for homeowners, landscapers, and farmers alike.

One of the standout features of the Bush Hog 2165 is its impressive cutting width of 65 inches, which allows it to cover large areas quickly and effectively. This makes it particularly suitable for tackling overgrown fields, pastures, and roadside maintenance tasks. The cutter is equipped with a powerful, heavy-duty gearbox that ensures reliable performance under various conditions, providing users with the confidence to handle even the most challenging cutting jobs.

The design of the Bush Hog 2165 emphasizes user safety and comfort. The model comes with a sturdy safety shield that protects operators from flying debris during operation. Additionally, the cutter features a tough, welded frame construction, which enhances its durability and ensures that it can withstand the rigors of repeated use.

Another notable technology incorporated into the Bush Hog 2165 is its adjustable cutting height feature. This allows users to set the desired grass height easily, ranging from 1 to 4 inches. This flexibility is crucial for achieving the perfect lawn look and accommodating different mowing requirements throughout the seasons.

The 2165 also includes high-capacity cutting blades designed to provide a clean and consistent cut. The blades can be replaced or sharpened easily, further enhancing the cutter's practicality and extending its lifespan. Furthermore, the model is compatible with a variety of tractors, making it a versatile attachment that fits seamlessly into many existing agricultural setups.

Overall, the Bush Hog 2165 rotary cutter is engineered for reliability and performance. Its blend of advanced technologies, safety features, and user-friendly design make it an excellent choice for anyone in need of a dependable mowing solution. Whether for personal gardening projects or professional landscape management, the Bush Hog 2165 excels in meeting the demands of diverse applications, ensuring users achieve their landscaping goals efficiently and effectively.
Top Page Image Contents