Bush Hog 2165 manual Stabilizer Pads, Troubleshooting Procedures

Page 19

STABILIZER PADS

Figure 10

 

 

The backhoe is supplied with flip-over stabilizer feet as standard equipment. They are suitable for most backhoe work and generally are all that is ever required. However, foot pad kits are available as options. These kits bolt to the standard feet and increase the versatility of the backhoe. See Figure 10.

Hydraulic Trouble Shooting

The trouble shooting material presented in this sec- tion is offered as a guide to diagnosing probable caus- es and remedies for general operational problems. Match your problem with the typical problem exam- ples given, and note the possible cause and the prop- er corrective action.

NOTE: When using the following chart, if it is decided that an overhaul of components or pressure adjust- ments are necessary to correct malfunctioning, it is

WARNING

Escaping hydraulic / diesel fluid under pressure can penetrate the skin causing serious injury.

Do not use your hand to check for leaks. Use a piece of cardboard or wood to check for leaks.

Stop engine and relieve pressure before con- necting or disconnecting lines.

recommended that your dealer make these repairs. He is equipped to do this work.

If any liquid is injected into the skin, obtain med- ical attention immediately or gangrene may result.

TROUBLESHOOTING PROCEDURES

Problem

Cause

Correction

Machine fails to operate

Low oil supply in reservoir

Fill to proper level.

when started initially

 

 

 

No oil supply to machine

Oil is not being diverted from the

 

 

prime mover hydraulic system.

 

 

Be sure that the proper controls are

 

 

actuated on the prime mover.

 

Pump not running

Check pump drive to be sure it is

 

 

engaged.

 

Improper hose connection

IMPORTANT: Be sure inlet and return

 

 

hoses are hooked up correctly.

 

 

Improper hook-up will result in

 

 

damage to the backhoe valve.

 

 

 

 

Excessive back pressure

Relieve condition. Restriction may be

 

 

from outlet to reservoir.

 

Relief valve setting in backhoe

Relief pressure will have to be checked

 

control valve too low or

and corrections made. Backhoe

 

defective

system pressure is 2400 PSI. Relief valve

 

 

may need cleaning and or overhauling or

 

 

entire cartridge must be replaced.

 

 

 

Machine loses power after

Low oil supply in

Fill to proper level.

operating satisfactorily

reservoir

 

initially

 

 

Loose oil line connections,

Tighten all hose connections and

 

 

leaks in line or broken lines

replace any damaged O-rings at

 

 

leaking O-ring fittings. Check and

 

 

replace any damaged hoses and lines.

 

 

 

 

Oil is bypassing cylinder piston,

Replace or rebuild the cylinder; replace

 

scored piston, worn piston

damaged parts.

 

packing, or defective piston

 

 

assembly

 

 

 

 

17

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Backhoes Congratulations Backhoes Table of ContentsDisclaimer of Implied Warranties & Consequential Damages This Limited Warranty Shall not Apply2165, 2175, 2185 and 2195 Backhoes Dealer Preparation Check ListYour Safety is Involved Safety Alert SymbolTractor Important Safety PrecautionsBackhoe Transportation Adjustments and InspectionAvoid HIGH-PRESSURE Fluids Osha Regulations EMPLOYERS, Employees and OperationsEmployee Tractor Operating Instructions This Act SeeksEngine Speed Keep bystanders a safe distance awayControls Operating the Backhoe Lock Pins Storage Tubes50102295 Transporting the BackhoePlacing the Stabilizers When TransportingDumping the Bucket Filling the BucketBackfilling Side Slope Excavating or TrenchingMiscellaneous Finishing Straight WallsHydraulic System Hoses ServiceBeginning of Season Bleeding Backhoe Hydraulic SystemOn Models 2165, 2175, 2185 and 2195 the follow Tooth ReplacementLubrication Tightening Nuts and BoltsRemoval from Tractor Storage Install the swing safety lock pin as shown in Figures 1Stabilizer Pads Troubleshooting ProceduresTroubleshooting Troubleshooting Load drops or settles Troubleshooting Troubleshooting Replace Center Section Assemblies Valve RepairReplacing Spool Seals General AssemblyMounting Backhoe to Tractor or Skid Steer loaders General DescriptionPoint Hitch Linkage 2165 Ag Tractor using 3-point hitchAssembly Refer to Figures 14 Point Hitch Linkage 2185/2195Assembly PTO Pump Kits Optional AssemblyDo not Remove Tractor PTO Guard Hydraulic HOOK-UP to TractorPage Closed Center System Backhoe Operation Hook-Up DiagramHydraulic Hook-Up 2175, 2185 Hook-Up RequirementsFor Tractors with OPEN-CENTER Hydraulic Systems Power Beyond KitsTractor Preparation Great Bend Backhoe & Great Bend Loader Valve Assembly Second ProcedureTractors with an auxiliary hydraulic flow of 15 gpm or less Flow Divider KIT OptionalGeneral Description Flow Divider Valve to Backhoe MountingFor Tractor Hydraulic Flow Greater than 15 GPM Testing Backhoe Hydraulic Hook-UpFlow Divider Valve to Skid Steer Adapter Mounting For Skid Steer Hydraulic For Skid Steer H Ydraulic Flow of 15 GPM or LessSeries Page Safety Decals Recommended Torque in Foot Pounds Newton Meters Torque SpecificationsBox 1039 Selma, AL 334

2165 specifications

The Bush Hog 2165 is a versatile and robust rotary cutter designed for heavy-duty lawn care and land management applications. This model is a part of the renowned Bush Hog lineup, known for its durability, efficiency, and ease of use. The 2165 strikes an excellent balance between performance and functionality, making it an ideal choice for homeowners, landscapers, and farmers alike.

One of the standout features of the Bush Hog 2165 is its impressive cutting width of 65 inches, which allows it to cover large areas quickly and effectively. This makes it particularly suitable for tackling overgrown fields, pastures, and roadside maintenance tasks. The cutter is equipped with a powerful, heavy-duty gearbox that ensures reliable performance under various conditions, providing users with the confidence to handle even the most challenging cutting jobs.

The design of the Bush Hog 2165 emphasizes user safety and comfort. The model comes with a sturdy safety shield that protects operators from flying debris during operation. Additionally, the cutter features a tough, welded frame construction, which enhances its durability and ensures that it can withstand the rigors of repeated use.

Another notable technology incorporated into the Bush Hog 2165 is its adjustable cutting height feature. This allows users to set the desired grass height easily, ranging from 1 to 4 inches. This flexibility is crucial for achieving the perfect lawn look and accommodating different mowing requirements throughout the seasons.

The 2165 also includes high-capacity cutting blades designed to provide a clean and consistent cut. The blades can be replaced or sharpened easily, further enhancing the cutter's practicality and extending its lifespan. Furthermore, the model is compatible with a variety of tractors, making it a versatile attachment that fits seamlessly into many existing agricultural setups.

Overall, the Bush Hog 2165 rotary cutter is engineered for reliability and performance. Its blend of advanced technologies, safety features, and user-friendly design make it an excellent choice for anyone in need of a dependable mowing solution. Whether for personal gardening projects or professional landscape management, the Bush Hog 2165 excels in meeting the demands of diverse applications, ensuring users achieve their landscaping goals efficiently and effectively.
Top Page Image Contents