Blount 633GC manual Drive Sprocket Installation, Spark Plug

Page 22

MAINTENANCE

633GC OPERATOR’S MANUAL

 

 

DRIVE SPROCKET INSTALLATION

•Slide the rim sprocket onto the splined adapter, either side out.

•Apply a liberal amount of grease to the needle bearing.

•Place the thin metal washer onto drive shaft. Slide the needle bearing and clutch cup w/rim sprocket onto shaft (Figure 1).

•Install the clutch by turning it counter clockwise on the drive shaft and firmly tighten. Replace the clutch slurry shield. Installation of drive sprocket assembly is now complete.

•The needle bearing on the drive shaft has to be greased regularly (daily). Use high quality water-resistant bearing grease.

•Bearing Tip: It is not necessary to remove the clutch cup to grease the bearing. There is a channel that goes directly from the drive shaft to the bearing (Figure 2). Simply inject grease directly into the end of the drive shaft.

Figure 1

Grease hole

Figure 2

SPARK PLUG

•A worn or fouled spark plug can cause a loss of power, difficulty starting or rough idle (Figure 3).

• If the spark plug is dirty, clean it with a wire brush and check the electrode gap. Readjust if necessary.

The correct gap is .020” (0.50mm).

• The spark plug should be replaced after 40 hours of operation

 

or earlier if the electrode is badly corroded.

Figure 3

 

•Always use the recommended spark plug type. Using the wrong spark plug can severely damage the piston and cylinder (Champion RCJ7Y).

22

© 2007 ICS, Blount Inc.

P/N 70944 Jan 07

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 633GC Page 633GC OPERATOR’S Manualtable of Contents Symbols & Labels 633GC OPERATOR’S Manual Following Symbol Applies to ALL the Items Listed on this Safety633GC OPERATOR’S Manual Following Symbol Applies to ALL Items Listed on this Safety 633GC OPERATOR’S ManualGeneral Safety Precautions Engine BREAK-IN Technical Specifications 633GC OPERATOR’S Manual Guide BAR and Diamond Chain Installation SET-UPSET-UP 633GC OPERATOR’S Manual SET-UP Fuel Mixing Operation 633GC OPERATOR’S ManualFuel Handling FuelingOperation Starting and Stopping a Diamond ChainsawPRE-CUT Checklist Planning the CUTCutting with the 633GC Cutting TipsSystem CLEAN-UP After 10 Hours of USE MaintenanceAfter Each USE After 40 Hours of USEStarter Housing Assembly Maintenance 633GC OPERATOR’S ManualAIR Filter Starter Rope Replacement Tensioning the Recoil SpringChain Tensioner Drive Sprocket Drive Sprocket RemovalDrive Sprocket Installation Spark PlugCarburetor Guide BarsMaintenance 633GC OPERATOR’S Manual 633GCTROUBLESHOOTINGPERATOR’S Manual Troubleshooting Further questions? Call 1-800-321-1240 or633GC OPERATOR’SREFERENCEMANUAL Approximate Cutting Rates INCH-FOOT DefinitionPage 633GC OPERATOR’S Manual

633GC specifications

The Blount 633GC is a robust and versatile piece of equipment designed for various industrial applications, particularly in construction and landscaping. It stands out due to its combination of advanced technologies, durability, and user-friendly features.

One of the standout features of the 633GC is its powerful engine. The unit is equipped with an efficient and high-performance engine that not only provides ample power for demanding tasks but also meets stringent emission standards. This balance of power and eco-friendliness makes the 633GC a reliable choice for modern job sites where environmental considerations are paramount.

The machine also boasts a state-of-the-art hydraulic system. This system ensures smooth and precise operation, allowing for enhanced control during lifting and digging tasks. The hydraulic components are designed for durability, reducing maintenance needs and increasing uptime, which is crucial for keeping projects on schedule.

Operator comfort and safety are prioritized in the design of the 633GC. The spacious cab features ergonomic controls and adjustable seating, making it easy for operators to stay comfortable even during long hours of work. Additionally, the cab is equipped with excellent visibility options, enabling operators to maintain awareness of their surroundings and enhance overall job site safety.

The chassis of the 633GC is built to last, featuring high-strength materials that can withstand the rigors of tough job sites. Its design provides excellent stability, making it suitable for operations on uneven terrain. Coupled with a well-designed tracking system, the 633GC ensures reliable gripping and maneuverability, whether on muddy job sites or steep inclines.

Technologically, the Blount 633GC incorporates advanced monitoring systems. These systems allow operators to track machine performance and maintenance needs in real-time, optimizing the operational lifespan of the equipment. The integration of smart technology provides actionable insights that can help prolong equipment life and reduce unexpected breakdowns.

In summary, the Blount 633GC is a powerful and reliable machine that combines advanced technology, operator comfort, and heavy-duty construction. It is ideal for those seeking a versatile solution for a variety of construction and landscaping tasks. With its robust features and commitment to efficiency, the 633GC remains a top contender in the market for industrial machinery.
Top Page Image Contents