Blount 633GC manual Further questions? Call 1-800-321-1240 or

Page 25

633GCTROUBLESHOOTINGPERATOR’S MANUAL

TROUBLESHOOTING

•SAW WON’T REACH FULL RPM – Air filter or pre filter may be dirty.

•SLOW CHAIN SPEED – Chain tension too tight. Chain should always be able to be pulled around the bar by hand. It is normal for the chain drive links to hang below the bar.

•POOR CUTTING SPEED – Diamonds may be “glazed over”. Make a few cuts in an abrasive material such as a cinder block to expose the diamonds.

•PREMATURE CHAIN STRETCH – Not enough water pressure. The minimum water pressure required is 20 psi (1.4 bar). Insufficient water supply may result in excessive wear to the diamond chain, which can lead to loss of strength and diamond chain breakage.

•CHAIN TENSIONER BREAKAGE – Side cover nuts are not tight enough. Torque to 20 ft-lbs (27Nm).

•WATER NOT FLOWING – Water hose is kinked or supply is not turned on.

•WON’T START – Turn ignition switch on or possible defective spark plug.

•WON’T START – Low compression, less than 120 psi (8 bar). Possible incorrect fuel mixture. Reference: new = 150 to 180 psi (10 to 12 bar)

used = 140 to 160 psi (9 to 11 bar)

•DIFFICULT TO START – Possible flooded engine. Turn ignition switch on, push choke in, hold throttle on full with foot and pull starter cord until engine starts.

•DIFFICULT TO START – Possible fouled spark plug. Remove spark plug, clean with wire brush and re-gap.

•CHAIN BREAKAGE – Chain installed backwards. Bumpers should lead segments into the cut.

•CHAIN BREAKAGE – Not enough feed pressure while cutting. Avoid letting the saw bounce and chatter.

Further questions?

Call 1-800-321-1240 or

visit our website at www.icsbestway.com

P/N 70944 Jan 07

© 2007 ICS, Blount Inc.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 633GC Page 633GC OPERATOR’S Manualtable of Contents Symbols & Labels 633GC OPERATOR’S Manual Following Symbol Applies to ALL the Items Listed on this Safety633GC OPERATOR’S Manual Following Symbol Applies to ALL Items Listed on this Safety 633GC OPERATOR’S ManualGeneral Safety Precautions Engine BREAK-IN Technical Specifications 633GC OPERATOR’S Manual SET-UP Guide BAR and Diamond Chain InstallationSET-UP 633GC OPERATOR’S Manual SET-UP Fuel Handling Operation 633GC OPERATOR’S ManualFuel Mixing FuelingStarting and Stopping a Diamond Chainsaw OperationPlanning the CUT PRE-CUT ChecklistCutting Tips Cutting with the 633GCSystem CLEAN-UP After Each USE MaintenanceAfter 10 Hours of USE After 40 Hours of USEStarter Housing Assembly Maintenance 633GC OPERATOR’S ManualAIR Filter Tensioning the Recoil Spring Starter Rope ReplacementChain Tensioner Drive Sprocket Removal Drive SprocketSpark Plug Drive Sprocket InstallationGuide Bars CarburetorMaintenance 633GC OPERATOR’S Manual Further questions? Call 1-800-321-1240 or 633GCTROUBLESHOOTINGPERATOR’S Manual TroubleshootingINCH-FOOT Definition 633GC OPERATOR’SREFERENCEMANUAL Approximate Cutting RatesPage 633GC OPERATOR’S Manual

633GC specifications

The Blount 633GC is a robust and versatile piece of equipment designed for various industrial applications, particularly in construction and landscaping. It stands out due to its combination of advanced technologies, durability, and user-friendly features.

One of the standout features of the 633GC is its powerful engine. The unit is equipped with an efficient and high-performance engine that not only provides ample power for demanding tasks but also meets stringent emission standards. This balance of power and eco-friendliness makes the 633GC a reliable choice for modern job sites where environmental considerations are paramount.

The machine also boasts a state-of-the-art hydraulic system. This system ensures smooth and precise operation, allowing for enhanced control during lifting and digging tasks. The hydraulic components are designed for durability, reducing maintenance needs and increasing uptime, which is crucial for keeping projects on schedule.

Operator comfort and safety are prioritized in the design of the 633GC. The spacious cab features ergonomic controls and adjustable seating, making it easy for operators to stay comfortable even during long hours of work. Additionally, the cab is equipped with excellent visibility options, enabling operators to maintain awareness of their surroundings and enhance overall job site safety.

The chassis of the 633GC is built to last, featuring high-strength materials that can withstand the rigors of tough job sites. Its design provides excellent stability, making it suitable for operations on uneven terrain. Coupled with a well-designed tracking system, the 633GC ensures reliable gripping and maneuverability, whether on muddy job sites or steep inclines.

Technologically, the Blount 633GC incorporates advanced monitoring systems. These systems allow operators to track machine performance and maintenance needs in real-time, optimizing the operational lifespan of the equipment. The integration of smart technology provides actionable insights that can help prolong equipment life and reduce unexpected breakdowns.

In summary, the Blount 633GC is a powerful and reliable machine that combines advanced technology, operator comfort, and heavy-duty construction. It is ideal for those seeking a versatile solution for a variety of construction and landscaping tasks. With its robust features and commitment to efficiency, the 633GC remains a top contender in the market for industrial machinery.
Top Page Image Contents