Aquatic Infinity Series owner manual Continuous Waterfall Infinity, Electrical Installation

Page 11

INSTALLATION INSTRUCTIONS

CONTINUOUS WATERFALL (INFINITY I):

The Infinity I is equipped with a continuous waterfall that is powered by a recirculation pump. The recirculation pump is plugged into your maintenance heater (see Diagram 4A, pg. 14). The maintenance heater must be plugged in for the continuous waterfall to be operational (see Diagram 4A, page 14). See page 16 for operation instructions.

ELECTRICAL INSTALLATION:

WARNING: ALL ELECTRICAL CONNECTIONS SHOULD BE MADE BY A LICENSED, LOCALLY CERTIFIED ELECTRICIAN, IN ACCORDANCE WITH THE REQUIREMENTS OF THE NATIONAL ELECTRICAL CODES AND PROCEDURES.

WARNING: WHEN USING ELECTRICAL PRODUCTS, PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:

DANGER: RISK OF ELECTRIC SHOCK!

GFCI’s are not supplied, however we do specify their use.

All known code authorities require GFCI’s.

The Infinity I - VIII will need to be hard wired to the outlets provided. See the following directions and diagram.

Two junction boxes will be mounted to the frame of the whirlpool. One of the two boxes will have one outlet and will be labeled “Blower”. Remove the cover and connect a 14/2 with ground Romex wire from a 15 amp 1-pole GFCI breaker (not supplied) in the main circuit breaker panel. Connect the black wire to the hot side of the receptacle, the white wire to the neutral side of the receptacle and the green wire to ground. Replace the cover and plug in the blower. (See diagram on page 13).

The second junction box will have two outlets, one labeled “Main” and the other labeled “Heater”. Remove the cover. Run Romex 14/3 with ground from a 15 amp 2-pole GFCI breaker (not supplied) located in the breaker panel. Connect the white wire (neutral) to both neutrals of the two outlets. Connect the red wire (hot) to the hot terminal of the outlet labeled “Main”. Connect the black wire (hot) to the hot terminal of the other outlet labeled “Heater”. Connect the green wire (ground) to the ground terminal of the outlet. Replace the cover of the junction box. Find the cord labeled “Heater AC Input” and plug it into the outlet labeled “Heater”. Plug the cord labeled “Main AC Input” into the outlet labeled “Main”. Both of these cords will come from the right side of the heater and will be marked. (See diagram on page 13).

12

AQUATIC INDUSTRIES, INC.

Image 11
Contents Infinity Series Table of Contents Purchase Registration Warranty ConfirmationOwner Information Congratulations Read and Follow ALL Instructions PRE-INSTALLATION Procedures Installation Instruction GuidelinesRead ALL Instructions Carefully Before Installation Structural Preparation Installation InstructionsLeveling of the Infinity Structural PreparationSee Illustration 2A Factory Installed Tile FlangePlumbing Fast Fill Waterfall Spout ROUGH-IN MeasurementsModel Continuous Waterfall Infinity Electrical InstallationBlower Please see Diagrams 4A and 4B.Infinity Electronic T-HEATER Model Number HS Chromatherapy LED Lighting Bathside Control Systems Infinity ON/OFF with Heater Control see Diagram 6AInfinity Series Whirlpools Infinity AIR Bath Control see Diagram 6C Infinity JET Sequencer Control see Diagram 6BPurge 24 Hours Infinity AIR Bath Purge Cycle see Diagram 6CJET Operations To adjust pressure see Diagram 7BTo replace or change jet see Diagram 7D To Remove/Replace Pillow see Diagram 8ATo replace or change jet see Diagram 9C To adjust pressure see Diagram 8BTo replace or change jet see Diagram 8C To adjust pressure see Diagram 9ATo replace or change jet see Diagram 11B To adjust pressure see Diagram 10ATo adjust circular pattern To adjust pressure see Diagram 11AFCC Consumer Information Electrical Installation Information Listed on pagesWhirlpool User Information AIR Bath System Cleaning Maintenance and CareInitial Cleaning Whirlpool System CleaningSurface Scratch Removal Surface CleaningJET Cleaning Water Quality IssuesChemical Quality Water Quality IssuesTreatment Symptoms Possible Problems Suggested Solutions Troubleshooting GuidePlease Fill OUT Completely Replacement Parts Order FormHow To Use Quantity Description Color/Finish PriceInfinity Series Replacement Parts Order MAPAssorted Fittings Replacement Parts Order MAP 27a 27b 28a 28b 28c F I N I T Y B a T H P a R T S L I S T Assorted Fittings Aquatic Industries, Inc. Limited Lifetime Warranty IOM6 12/05