Aquatic Infinity Series owner manual Read and Follow ALL Instructions

Page 5

IMPORTANT SAFETY INSTRUCTIONS

WARNING: WHEN USING THIS UNIT, THESE BASIC PRECAUTIONS SHOULD BE FOLLOWED.

This manual contains information and instructions for proper operation and maintenance of your whirlpool. Failure to follow these instructions could result in personal injury, electrical shock or fire.

READ AND FOLLOW ALL INSTRUCTIONS

DANGER! TO REDUCE THE RISK OF INJURY:

A.Do not permit children to use this unit unless they are closely supervised by an adult at all times. Supervision is also required when whirlpool bath is used by an elderly or handicapped individual.

B.Use this unit only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.

C.Do not operate this unit without guard over the suction fitting.

D.The water in a whirlpool should never exceed 40°C (104°F). Water temperatures between 38°C (100°F) and 40°C (104°F) are considered safe for a healthy adult. Use time should be limited to approximately 30 minutes, followed by a shower to cool down. Longer exposures may result in hyperthermia. The symptoms of this condition are nausea, dizziness and fainting, which can be fatal. Lower water temperatures are recommended for extended use (exceeding 10-15 minutes) and for young children.

E.Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy, pregnant or possibly pregnant women should limit whirlpool water temperatures to 38°C (100°F).

F.The use of drugs or alcoholic beverages before or during whirlpool use may lead to unconsciousness with the possibility of drowning. Never use the whirlpool while under the influence of alcohol, anticoagulants, stimulants, antihistamines, vasoconstrictors, vasodilators, hypnotics, narcotics or tranquilizers.

G.Persons with a medical history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using a whirlpool.

H.Persons using medication should consult a physician before using a whirlpool since medication may induce drowsiness while other medication may affect heart rate, blood pressure and circulation.

DANGER: To reduce the risk of injury, enter and exit the bath slowly.

WARNING: Never operate electrical devices in or near the bath. Never drop or insert any object into any opening within the whirlpool.

This unit must be connected to a supply circuit that is protected by a Ground Fault Circuit Interrupter (GFCI). Such a device should be installed by a licensed electrician and should be tested on a regular basis (at least monthly). To test the GFCI push the TEST button. The GFCI should interrupt the power. Push the RESET button and the power should be restored. If the GFCI fails to operate in this manner there is the possibility of an electric shock. DO NOT USE. Disconnect the unit and have the problem corrected by a qualified service technician. To avoid the possibility of personal injury and discoloration of the acrylic surface, the inlet water temperature should not exceed 60°C (140°F). The bath should be drained after each use. Each bather should start their bath with fresh water.

CAUTION: DO NOT USE HARSH ABRASIVES OR SOLVENTS FOR CLEANING THIS UNIT.

INSTALLER/OWNER BEARS ALL RESPONSIBILITY TO COMPLY WITH ALL STATE AND LOCAL CODES

WHEN INSTALLING THIS PRODUCT.

SAVE THESE INSTRUCTIONS

6

AQUATIC INDUSTRIES, INC.

Image 5
Contents Infinity Series Table of Contents Purchase Registration Warranty ConfirmationOwner Information Congratulations Read and Follow ALL Instructions PRE-INSTALLATION Procedures Installation Instruction GuidelinesRead ALL Instructions Carefully Before Installation Structural Preparation Installation InstructionsLeveling of the Infinity Structural PreparationSee Illustration 2A Factory Installed Tile FlangePlumbing Fast Fill Waterfall Spout ROUGH-IN MeasurementsModel Continuous Waterfall Infinity Electrical InstallationBlower Please see Diagrams 4A and 4B.Infinity Electronic T-HEATER Model Number HS Chromatherapy LED Lighting Bathside Control Systems Infinity ON/OFF with Heater Control see Diagram 6AInfinity Series Whirlpools Infinity AIR Bath Control see Diagram 6C Infinity JET Sequencer Control see Diagram 6BPurge 24 Hours Infinity AIR Bath Purge Cycle see Diagram 6CTo replace or change jet see Diagram 7D To adjust pressure see Diagram 7BTo Remove/Replace Pillow see Diagram 8A JET OperationsTo replace or change jet see Diagram 8C To adjust pressure see Diagram 8BTo adjust pressure see Diagram 9A To replace or change jet see Diagram 9CTo adjust circular pattern To adjust pressure see Diagram 10ATo adjust pressure see Diagram 11A To replace or change jet see Diagram 11BFCC Consumer Information Electrical Installation Information Listed on pagesWhirlpool User Information Initial Cleaning Maintenance and CareWhirlpool System Cleaning AIR Bath System CleaningJET Cleaning Surface CleaningWater Quality Issues Surface Scratch RemovalChemical Quality Water Quality IssuesTreatment Symptoms Possible Problems Suggested Solutions Troubleshooting GuideHow To Use Replacement Parts Order FormQuantity Description Color/Finish Price Please Fill OUT CompletelyInfinity Series Replacement Parts Order MAPAssorted Fittings Replacement Parts Order MAP 27a 27b 28a 28b 28c F I N I T Y B a T H P a R T S L I S T Assorted Fittings Aquatic Industries, Inc. Limited Lifetime Warranty IOM6 12/05