Aquatic Infinity Series owner manual Infinity JET Sequencer Control see Diagram 6B

Page 16

OPERATION of

INFINITY SERIES WHIRLPOOLS

BATHSIDE CONTROL SYSTEMS (continued):

INFINITY JET SEQUENCER CONTROL (SEE DIAGRAM 6B):

1.To Turn Jet Sequencer On: Pressing the “On/Off” button will turn the jet sequencer on. The system will then perform an indicator light test and open all valves. Pressing the “On/Off” button a second time will turn the jet sequencer off. A built-in timer automatically turns the jet sequencer off after 2 hours, unless manually deactivated first. Note: Pump must be turned on for the jet sequencer to be effective (see “Infinity On/Off with Heater Control” above.)

2.To Choose Sequences: Press the “Sequences” button to select one of the 7 preprogrammed massage sequences. Note: Only the first 6 sequences have corresponding indicator lights. The remaining sequences do not have indicator lights. A preview of the massage is displayed for 5 seconds after selecting a sequence.

3. To Change Speeds: Press the “Speeds” button to

6B

change the time interval between each step of the

 

selected massage sequence.

 

Speed 1:

15

Seconds between each step.

 

Speed 2:

10

Seconds between each step.

 

Speed 3:

5

Seconds between each step.

 

4.To Pause: Press the “Pause” button to interrupt a massage sequence and prolong the action of a jet set for a combination of sets. Pressing a second time will resume the massage sequence. The “Pause” indicator light will be on in “Pause” mode.

Other Features:

Automatic purge: Thirty minutes after the jet sequencer has shut off, the solenoids will open and close to drain any water from the pipes.

INFINITY AIR BATH CONTROL (SEE DIAGRAM 6C):

1.To Turn Air Bath System On: Pressing the On/Off button will turn the blower on in “constant mode.” Once the blower is on, pressing a second time will turn the

blower off. The light indicator will illuminate when the

system is on. The blower and the blower heater will

 

automatically shut off after a 20-minute period.

 

2. To Change Modes: Pressing the Mode

button

6C

alternates the blower modes of operation from constant

 

mode to wave mode and then to pulse mode.

Constant Mode: Consists of a constant blower level with no change. The light indicator will also follow the blower intensity set by the user.

Wave Mode: Consists of a gradual change of blower level to generate a gentle massage effect. The light indicator will also follow the blower intensity.

Pulse Mode: Consists of an instant change of the blower level to generate a massage effect. The light indicator will also pulse as the blower does.

AQUATIC INDUSTRIES, INC.

17

Image 16
Contents Infinity Series Table of Contents Owner Information Warranty ConfirmationPurchase Registration Congratulations Read and Follow ALL Instructions Read ALL Instructions Carefully Before Installation Installation Instruction GuidelinesPRE-INSTALLATION Procedures Installation Instructions Structural PreparationStructural Preparation Leveling of the InfinityPlumbing Factory Installed Tile FlangeSee Illustration 2A Model ROUGH-IN MeasurementsFast Fill Waterfall Spout Electrical Installation Continuous Waterfall InfinityPlease see Diagrams 4A and 4B. BlowerInfinity Electronic T-HEATER Model Number HS Chromatherapy LED Lighting Infinity Series Whirlpools Infinity ON/OFF with Heater Control see Diagram 6ABathside Control Systems Infinity JET Sequencer Control see Diagram 6B Infinity AIR Bath Control see Diagram 6CInfinity AIR Bath Purge Cycle see Diagram 6C Purge 24 HoursTo adjust pressure see Diagram 7B To replace or change jet see Diagram 7DTo Remove/Replace Pillow see Diagram 8A JET OperationsTo adjust pressure see Diagram 8B To replace or change jet see Diagram 8CTo adjust pressure see Diagram 9A To replace or change jet see Diagram 9CTo adjust pressure see Diagram 10A To adjust circular patternTo adjust pressure see Diagram 11A To replace or change jet see Diagram 11BWhirlpool User Information Electrical Installation Information Listed on pagesFCC Consumer Information Maintenance and Care Initial CleaningWhirlpool System Cleaning AIR Bath System CleaningSurface Cleaning JET CleaningWater Quality Issues Surface Scratch RemovalWater Quality Issues Chemical QualityTreatment Troubleshooting Guide Symptoms Possible Problems Suggested SolutionsReplacement Parts Order Form How To UseQuantity Description Color/Finish Price Please Fill OUT CompletelyReplacement Parts Order MAP Infinity SeriesAssorted Fittings Replacement Parts Order MAP 27a 27b 28a 28b 28c F I N I T Y B a T H P a R T S L I S T Assorted Fittings Aquatic Industries, Inc. Limited Lifetime Warranty IOM6 12/05