Aquatic Infinity Series owner manual Infinity AIR Bath Purge Cycle see Diagram 6C, Purge 24 Hours

Page 17

OPERATION of

INFINITY SERIES WHIRLPOOLS

BATHSIDE CONTROL SYSTEMS (continued):

INFINITY AIR BATH CONTROL (SEE DIAGRAM 6C) (continued):

3.To Change Speeds: In constant mode, pressing and holding the “+” button will increase the variable speed of the blower to the maximum. Pressing and holding the “—” button will reduce the blower’s variable speed to the minimum. In both cases, the user can release the button at the desired power level. Note: In wave mode or pulse mode, the “+” or “—” buttons will work the same way but will have an effect on the maximum power of the wave and pulse mode.

INFINITY AIR BATH PURGE CYCLE (SEE DIAGRAM 6C):

Following the 20 minute run time of the blower, there will be a 15 minute idle period. The blower will then turn on for 3 minutes for the purge cycle. If the user turns the blower off manually before the timer reaches 20 minutes, the idle period will start after the blower has been turned off. During the 15 minute idle period and the 3 minutes purge, the light indicator of the on/off button will blink. During the idle period, pressing the on/off button will turn on the blower in constant mode. During the 3 minute purge, pressing the blower key will stop the purge.

PURGE 24 HOURS

It is possible for the user to program a purge cycle that will start every day for a duration of 1 minute. Aquatic strongly recommends activating this feature. The purge cycle will help ensure that the air channels stay dry even when you have taken a soaking bath or shower.

To activate this purge feature, the user must hold down the “+” button for 5 seconds when the blower/ heater is off or waiting for the normal purge. Then, the light indicator on the on/off button will blink twice. If the unit was in standby for a normal purge when the 24 hour purge was activated, the normal purge will be cancelled.

To show the user that the 24 hour purge is activated, the light indicator on the on/off button will blink at a slow rate. A different blinking rate was picked in order to make it easier for the user to differentiate it from the standby of the regular purge cycle.

The purge will be done every day at the same time the user activated it (pressed the “+” button). By pressing the “+” button again, the 24 hour purge will be deactivated and the light indicator on the on/ off button will stop blinking and turn off.

18

AQUATIC INDUSTRIES, INC.

Image 17
Contents Infinity Series Table of Contents Purchase Registration Warranty ConfirmationOwner Information Congratulations Read and Follow ALL Instructions PRE-INSTALLATION Procedures Installation Instruction GuidelinesRead ALL Instructions Carefully Before Installation Structural Preparation Installation InstructionsLeveling of the Infinity Structural PreparationSee Illustration 2A Factory Installed Tile FlangePlumbing Fast Fill Waterfall Spout ROUGH-IN MeasurementsModel Continuous Waterfall Infinity Electrical InstallationBlower Please see Diagrams 4A and 4B.Infinity Electronic T-HEATER Model Number HS Chromatherapy LED Lighting Bathside Control Systems Infinity ON/OFF with Heater Control see Diagram 6AInfinity Series Whirlpools Infinity AIR Bath Control see Diagram 6C Infinity JET Sequencer Control see Diagram 6BPurge 24 Hours Infinity AIR Bath Purge Cycle see Diagram 6CTo replace or change jet see Diagram 7D To adjust pressure see Diagram 7BTo Remove/Replace Pillow see Diagram 8A JET OperationsTo replace or change jet see Diagram 8C To adjust pressure see Diagram 8BTo adjust pressure see Diagram 9A To replace or change jet see Diagram 9CTo adjust circular pattern To adjust pressure see Diagram 10ATo adjust pressure see Diagram 11A To replace or change jet see Diagram 11BFCC Consumer Information Electrical Installation Information Listed on pagesWhirlpool User Information Initial Cleaning Maintenance and CareWhirlpool System Cleaning AIR Bath System CleaningJET Cleaning Surface CleaningWater Quality Issues Surface Scratch RemovalChemical Quality Water Quality IssuesTreatment Symptoms Possible Problems Suggested Solutions Troubleshooting GuideHow To Use Replacement Parts Order FormQuantity Description Color/Finish Price Please Fill OUT CompletelyInfinity Series Replacement Parts Order MAPAssorted Fittings Replacement Parts Order MAP 27a 27b 28a 28b 28c F I N I T Y B a T H P a R T S L I S T Assorted Fittings Aquatic Industries, Inc. Limited Lifetime Warranty IOM6 12/05