Aquatic Infinity Series owner manual Factory Installed Tile Flange, Plumbing, See Illustration 2A

Page 9

INSTALLATION INSTRUCTIONS

FACTORY INSTALLED TILE FLANGE:

SEE ILLUSTRATION 2A

A.Install the whirlpool bath unit per the instructions provided in this manual.

CAUTION: THE TILE FLANGE DOES NOT SUPPORT THE TUB! A ledger board must be provided under the bath rim as indicated in the installation instructions. Take care to ensure tub is not hanging from the ledger boards, as this will void your warranty.

B.Use nails or screws to secure the flange into the studs around the bath.

C.Install water resistant drywall against the tile flange and flush to the top of the whirlpool deck. Install the tile or other finishing materials. Apply a second bead of silicone between the first course of tile and the bath deck.

2A

NOTE: Before tub is used, the whirlpool system should be cleaned in accordance

with the procedures on Page 23 of this manual.

PLUMBING:

1.After securing tub in place, normal waste and overflow and valves are installed per normal plumbing procedures, in accordance with all state and local standards.

2.Install standard 1-1/2" trap to drain and overflow. Before proceeding, make a final operational check by filling tub with water to overflow and operate pump for 5 minutes. Check for leaks carefully both while pump is running and has been turned off. Allow water to stand in tub for at least 30 minutes before draining.

AQUATIC INDUSTRIES, INC. WILL NOT BE RESPONSIBLE FOR WATER DAMAGE OF ANY KIND IN CONNECTION WITH ONE OF OUR WHIRLPOOL BATHS.

3.All Infinity Series models are equipped with an integral Fast Fill Waterfall Spout. Purchasing a spout is unnecessary, however, hot and cold water valves are needed. Valves can be mounted where you choose, however, if installation is to be on the tub deck, check the back side of the tub for adequate space for connection to water lines before drilling or cutting tub.

10

AQUATIC INDUSTRIES, INC.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Infinity Series Table of Contents Warranty Confirmation Owner InformationPurchase Registration Congratulations Read and Follow ALL Instructions Installation Instruction Guidelines Read ALL Instructions Carefully Before InstallationPRE-INSTALLATION Procedures Structural Preparation Installation InstructionsLeveling of the Infinity Structural PreparationFactory Installed Tile Flange PlumbingSee Illustration 2A ROUGH-IN Measurements ModelFast Fill Waterfall Spout Continuous Waterfall Infinity Electrical InstallationBlower Please see Diagrams 4A and 4B.Infinity Electronic T-HEATER Model Number HS Chromatherapy LED Lighting Infinity ON/OFF with Heater Control see Diagram 6A Infinity Series WhirlpoolsBathside Control Systems Infinity AIR Bath Control see Diagram 6C Infinity JET Sequencer Control see Diagram 6BPurge 24 Hours Infinity AIR Bath Purge Cycle see Diagram 6CTo replace or change jet see Diagram 7D To adjust pressure see Diagram 7BTo Remove/Replace Pillow see Diagram 8A JET OperationsTo replace or change jet see Diagram 8C To adjust pressure see Diagram 8BTo adjust pressure see Diagram 9A To replace or change jet see Diagram 9CTo adjust circular pattern To adjust pressure see Diagram 10ATo adjust pressure see Diagram 11A To replace or change jet see Diagram 11BElectrical Installation Information Listed on pages Whirlpool User InformationFCC Consumer Information Initial Cleaning Maintenance and CareWhirlpool System Cleaning AIR Bath System CleaningJET Cleaning Surface CleaningWater Quality Issues Surface Scratch RemovalChemical Quality Water Quality IssuesTreatment Symptoms Possible Problems Suggested Solutions Troubleshooting GuideHow To Use Replacement Parts Order FormQuantity Description Color/Finish Price Please Fill OUT CompletelyInfinity Series Replacement Parts Order MAPAssorted Fittings Replacement Parts Order MAP 27a 27b 28a 28b 28c F I N I T Y B a T H P a R T S L I S T Assorted Fittings Aquatic Industries, Inc. Limited Lifetime Warranty IOM6 12/05
Top Page Image Contents