Exmark S/N 790 Specifications, Model Numbers, Systems, Engine, Fuel System, Electrical System

Page 14
Specifications

Specifications

Specifications

Model Numbers

Serial Nos: 790,000 and Higher

LZZ23KC486; LZZ23KA526; LZZ23KC526; LZZ27KC526; LZZ27KC606; LZZ29KA606; LZZ34KA606; LZZ34KA726

Systems

Engine

Engine Specifications: See your Engine Owner’s Manual

RPM: Full Speed: 3750 ±50 RPM (PTO not

engaged) Idle: 1500 RPM

Fuel System

Capacity: 12.0 gal. (45.4 L)

Type of Fuel: Regular unleaded gasoline, 87 octane or higher.

Fuel Filter:

Kohler:

Kohler P/N 24 050 13

Kawasaki:

Kawasaki P/N 49019-7001

Fuel Shut-Off Valve:

All Units: 1/4 turn increments (“ON”, “OFF”).

Fuel level eight segment display — right hand control panel.

Low fuel indicator light.

Electrical System

Charging System: Flywheel Alternator

Charging Capacity:

Kohler and Kawasaki: 15 amps

Battery Type: BCI Group U1

Recommended Minimum Battery CCA:

34HP Kawasaki: 340 CCA

All other engines: 260 CCA

Battery Voltage: 12 Volt

Low Voltage Light — RH control panel

Polarity: Negative Ground

Fuses:

All units:

25 amp main fuse

25 amp charging system fuse

10 amp PTO fuse

15 amp accessory fuse

Safety Interlock System

LCD indicators appear for the PTO, park brake, drive levers, and operator presence in the message display on the RH control panel.

PTO must be disengaged, brake engaged, and motion control levers out (neutral lock) to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

Operator must be in seat when PTO is engaged, brake is disengaged, or motion control levers are moved in or engine will stop.

Engine will stop if either the left, the right, or both levers are moved from neutral lock position while brake is engaged.

Operator Controls

Steering and Motion Control:

Note: Motion control levers are adjustable to two heights.

Separate levers, on each side of the console, control speed and direction of travel of the respective drive wheels.

Steering is controlled by varying the position of the levers relative to each other.

Moving motion control levers outward (in slots) locks the drive system in neutral.

PTO Engagement Switch: Engages electric clutch (to drive belt) which engages mower blades.

Parking Brake Lever: Engages parking brake.

Parking Brake Release Button: Releases parking brake.

14

Image 14
Contents Part No. 4500-471Rev. A LAZER Z MODELSFor Serial Nos 790,000 & Higher CALIFORNIA Proposition 65 Warning Introduction Model No Serial NoContents Safety SafetySafety Alert Symbol Safe Operating PracticesDANGER DANGERSafety Operation SafetySafety Using the Rollover Protection System ROPSSlope Operation Do Not mow slopes when grass is wetMaintenance and Storage SafetySafety and Instructional Decals Safety109-7232 Safety109-3148 107-2102 109-7330 107-2112109-9361 Safety109-8483 Deck Drive Belt Routing116-0211 SafetyPTO Switch Symbols Message DisplaySafety Interlock System SpecificationsSpecifications Model NumbersTires & Wheels SeatHydrostatic Ground Drive System SpecificationsOverall Width DimensionsCutting Deck Overall LengthTread Width Center to Center of Tires, Widthwise Curb WeightAccessory Weight Table Worksheet SpecificationsProduct Overview Product OverviewTorque Requirements Operation OperationControls Motion Control LeversOperation Ignition SwitchHour Meter Fuel Shut-OffValve PTO Engagement SwitchLow Voltage Indicator Fuel GaugeDeck Lift Pedal Operating InstructionsPre-Start Transport LockEngaging the PTO Open the Fuel Shut-OffValveStarting the Engine Disengaging the PTOUse caution when making turns Stopping the EngineDriving the Machine OperationOperation Adjusting the Cutting HeightAdjusting the Anti-ScalpRollers Driving in ReverseOperation TransportingTransporting a Unit Loading a Unit OperationMaintenance MaintenanceRecommended Maintenance Schedules Service Interval Before each use or daily Periodic MaintenanceCheck Battery Charge Service Interval As requiredMaintenance Check Safety Interlock SystemCheck Mower Blades Service Interval Before each use or dailyCheck Seat Belt Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check for Loose HardwareChange Engine Oil Service Interval After the first 5 hoursService Interval Every 50 hours Check Hydraulic Oil LevelLubricate Caster Wheel Hubs Check Condition Of BeltsLubricate Grease Fittings MaintenanceService Interval Every 500 hours Service Interval Every 200 hoursService Interval Every 100 hours Lubricate Brake Handle PivotCheck Spark Arrester if equipped Wheel Hub - Slotted Nut Torque SpecificationService Interval After the first 100 hours Every 500 hours thereafterCopper-Based Anti-seize AdjustmentsThread Locking Adhesives Dielectric GreaseMaintenance 8.Raise the discharge deflectorDeck Removal MaintenanceDeck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension MaintenanceMotion Control Damper Adjustment Electric Clutch AdjustmentMotion Control Linkage Adjustment MaintenanceMotion Control Full Forward Tracking Adjustment Motion Control Handle AdjustmentMotion Control Neutral Lock Pivot Adjustment MaintenanceRH Motion Control Shown Caster Pivot Bearings Pre-LoadAdjustmentMaintenance Remove Engine Shrouds and Clean Cooling Fins CleaningClean Engine and Exhaust System Area Clean Hydro Fan Cooling GuardsMotor Oil Disposal Battery DisposalWaste Disposal MaintenanceTroubleshooting TroubleshootingPossible Cause TroubleshootingProblem Corrective ActionElectrical Diagram SchematicsSchematics PINKSchematics SchematicElectrical LogicHydraulic Diagram Schematics5 Year or 750 Hours Limited Consumer Warranty Exmark Lazer Z and Lazer Z AS Turf Equipment3 Year Limited Commercial Warranty General Warranty Conditions and Products CoveredPage Page Date Service RecordService Done By Description of Work DonePage Page WALK-BEHINDACCESSORIES AND OPTIONS MID-MOUNTRIDING ACCESSORIES AND OPTIONSOUT-FRONTRIDING ACCESSORIES AND OPTIONS
Related manuals
Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.