Exmark S/N 790 Motion Control Handle Adjustment, Motion Control Neutral Lock Pivot Adjustment

Page 41
Motion Control Handle Adjustment

Maintenance

Motion Control Handle Adjustment

Adjusting the height:

The motion control levers can be adjusted higher or lower for maximum operator comfort.

1.Remove the two bolts holding the control lever to the control arm shaft (Figure 34).

Figure 32

RH Motion Control Shown

1.Torque nyloc nut to 200 in-lb (16.7 ft-lb). Bolt must protrude past end of nyloc nut after torque. A T-40 Torx bit will be necessary to hold the stud from turning.

2.Most resistance (firmest feel)

3.Damper

4.Medium resistance (medium feel)

5.Least resistance (softest feel)

Motion Control Neutral Lock Pivot Adjustment

The flanged nut can be adjusted to obtain a more desired motion control lever resistance (Figure 33).

Figure 33

1. Flanged nut

2. Jam nut

1.Loosen the jam nut.

2.Tighten or loosen the flanged nut to the desired feel.

For more resistance, tighten the flanged nut. For less resistance, loosen the flanged nut

3.Tighten jam nut.

Figure 34

1.

Bolts

4.

Nuts

2.

Control lever

5.

Slotted holes

3.Control arm shaft

2.Move the control lever to the next set of holes. Secure the lever with the two bolts.

3.Repeat the adjustment for the opposite control lever.

Adjusting the Tilt

The motion control levers can be tilted fore or aft for maximum operator comfort.

1.Loosen the upper bolt holding the control lever to the control arm shaft.

2.Loosen the lower bolt just enough to pivot the control lever fore or aft Figure 34. Tighten both bolts to secure the control in the new position.

3.Repeat the adjustment for the opposite control lever.

Motion Control Full Forward Tracking Adjustment

If the machine travels or pulls to one side when the motion control levers are in the full forward position, adjust the cover plates.

1. Loosen the screws on a cover plate (see Figure 35).

41

Image 41
Contents Part No. 4500-471Rev. A LAZER Z MODELSFor Serial Nos 790,000 & Higher CALIFORNIA Proposition 65 Warning Model No Serial No IntroductionContents Safety Alert Symbol SafetySafety Safe Operating PracticesDANGER DANGERSafety Safety OperationSlope Operation Using the Rollover Protection System ROPSSafety Do Not mow slopes when grass is wetSafety Maintenance and StorageSafety Safety and Instructional Decals109-3148 Safety109-7232 107-2102 109-7330 107-2112109-8483 Safety109-9361 Deck Drive Belt RoutingPTO Switch Symbols Safety116-0211 Message DisplaySpecifications SpecificationsSafety Interlock System Model NumbersHydrostatic Ground Drive System SeatTires & Wheels SpecificationsCutting Deck DimensionsOverall Width Overall LengthAccessory Weight Table Worksheet Curb WeightTread Width Center to Center of Tires, Widthwise SpecificationsProduct Overview Product OverviewTorque Requirements Controls OperationOperation Motion Control LeversOperation Ignition SwitchHour Meter Low Voltage Indicator PTO Engagement SwitchFuel Shut-OffValve Fuel GaugePre-Start Operating InstructionsDeck Lift Pedal Transport LockStarting the Engine Open the Fuel Shut-OffValveEngaging the PTO Disengaging the PTODriving the Machine Stopping the EngineUse caution when making turns OperationAdjusting the Anti-ScalpRollers Adjusting the Cutting HeightOperation Driving in ReverseOperation TransportingTransporting a Unit Operation Loading a UnitMaintenance MaintenanceRecommended Maintenance Schedules Check Battery Charge Periodic MaintenanceService Interval Before each use or daily Service Interval As requiredCheck Mower Blades Check Safety Interlock SystemMaintenance Service Interval Before each use or dailyCheck Rollover Protections Systems Roll Bar Knobs Service Air CleanerCheck Seat Belt Check for Loose HardwareService Interval Every 50 hours Service Interval After the first 5 hoursChange Engine Oil Check Hydraulic Oil LevelLubricate Grease Fittings Check Condition Of BeltsLubricate Caster Wheel Hubs MaintenanceService Interval Every 100 hours Service Interval Every 200 hoursService Interval Every 500 hours Lubricate Brake Handle PivotService Interval After the first 100 hours Wheel Hub - Slotted Nut Torque SpecificationCheck Spark Arrester if equipped Every 500 hours thereafterThread Locking Adhesives AdjustmentsCopper-Based Anti-seize Dielectric Grease8.Raise the discharge deflector MaintenanceMaintenance Deck RemovalPump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension MaintenanceMotion Control Linkage Adjustment Electric Clutch AdjustmentMotion Control Damper Adjustment MaintenanceMotion Control Neutral Lock Pivot Adjustment Motion Control Handle AdjustmentMotion Control Full Forward Tracking Adjustment MaintenanceRH Motion Control Shown Caster Pivot Bearings Pre-LoadAdjustmentMaintenance Clean Engine and Exhaust System Area CleaningRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling GuardsWaste Disposal Battery DisposalMotor Oil Disposal MaintenanceTroubleshooting TroubleshootingProblem TroubleshootingPossible Cause Corrective ActionSchematics SchematicsElectrical Diagram PINKElectrical SchematicSchematics LogicSchematics Hydraulic Diagram3 Year Limited Commercial Warranty Exmark Lazer Z and Lazer Z AS Turf Equipment5 Year or 750 Hours Limited Consumer Warranty General Warranty Conditions and Products CoveredPage Page Service Done By Service RecordDate Description of Work DonePage Page WALK-BEHINDACCESSORIES AND OPTIONS MID-MOUNTRIDING ACCESSORIES AND OPTIONSOUT-FRONTRIDING ACCESSORIES AND OPTIONS
Related manuals
Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.