Exmark 000 & higher, 4500-471, S/N 790 manual Loading a Unit, Operation

Page 27
Loading a Unit

Operation

Manual background WARNING

Loading a unit on a trailer or truck increases the possibility of backward tip-over. Backward tip-over could cause serious injury or death.

•Use extreme caution when operating a unit on a ramp.

•Use only a single, full width ramp; Do Not use individual ramps for each side of the unit.

•If individual ramps must be used, use enough ramps to create an unbroken ramp surface wider than the unit.

•Do Not exceed a 15° angle between ramp and ground or between ramp and trailer or truck.

•Avoid sudden acceleration while driving unit up a ramp to avoid tipping backward.

•Avoid sudden deceleration while backing unit down a ramp to avoid tipping backward.

Loading a Unit

Use extreme caution when loading units on trailers or trucks. One full width ramp that is wide enough to extend beyond the rear tires is recommended instead of individual ramps for each side of the unit. The lower rear section of the tractor frame extends back between the rear wheels and serves as a stop for tipping backward. Having a full width ramp provides a surface for the frame members to contact if the unit starts to tip backward. If it is not possible to use one full width ramp, use enough individual ramps to simulate a full width continuous ramp.

Ramp should be long enough so that the angles between the ramp and the ground and the ramp and the trailer or truck do not exceed 15°. A steeper angle may cause mower deck components to get caught as the unit moves from ramp to trailer or truck. Steeper angles may also cause the unit to tip backward. If loading on or near a slope, position the trailer or truck so it is on the down side of the slope and the ramp extends up the slope. This will minimize the ramp angle. The trailer or truck should be as level as possible.

Important: Do Not attempt to turn the unit while on the ramp, you may lose control and drive off the side.

Avoid sudden acceleration when driving up a ramp and sudden deceleration when backing down a ramp. Both maneuvers can cause the unit to tip backward.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents LAZER Z MODELS For Serial Nos 790,000 & HigherPart No. 4500-471Rev. A CALIFORNIA Proposition 65 Warning Model No Serial No IntroductionContents Safe Operating Practices SafetySafety Alert Symbol SafetyDANGER SafetyDANGER Safety OperationDo Not mow slopes when grass is wet Using the Rollover Protection System ROPSSlope Operation SafetySafety Maintenance and StorageSafety Safety and Instructional Decals107-2102 109-7330 107-2112 Safety109-3148 109-7232Deck Drive Belt Routing Safety109-8483 109-9361Message Display SafetyPTO Switch Symbols 116-0211Model Numbers SpecificationsSpecifications Safety Interlock SystemSpecifications SeatHydrostatic Ground Drive System Tires & WheelsOverall Length DimensionsCutting Deck Overall WidthSpecifications Curb WeightAccessory Weight Table Worksheet Tread Width Center to Center of Tires, WidthwiseProduct Overview Torque RequirementsProduct Overview Motion Control Levers OperationControls OperationIgnition Switch Hour MeterOperation Fuel Gauge PTO Engagement SwitchLow Voltage Indicator Fuel Shut-OffValveTransport Lock Operating InstructionsPre-Start Deck Lift PedalDisengaging the PTO Open the Fuel Shut-OffValveStarting the Engine Engaging the PTOOperation Stopping the EngineDriving the Machine Use caution when making turnsDriving in Reverse Adjusting the Cutting HeightAdjusting the Anti-ScalpRollers OperationTransporting Transporting a UnitOperation Operation Loading a UnitMaintenance Recommended Maintenance SchedulesMaintenance Service Interval As required Periodic MaintenanceCheck Battery Charge Service Interval Before each use or dailyService Interval Before each use or daily Check Safety Interlock SystemCheck Mower Blades MaintenanceCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltCheck Hydraulic Oil Level Service Interval After the first 5 hoursService Interval Every 50 hours Change Engine OilMaintenance Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Brake Handle Pivot Service Interval Every 200 hoursService Interval Every 100 hours Service Interval Every 500 hoursEvery 500 hours thereafter Wheel Hub - Slotted Nut Torque SpecificationService Interval After the first 100 hours Check Spark Arrester if equippedDielectric Grease AdjustmentsThread Locking Adhesives Copper-Based Anti-seize8.Raise the discharge deflector MaintenanceMaintenance Deck RemovalMaintenance Adjusting the Parking BrakePump Drive Belt Tension Deck Belt TensionMaintenance Electric Clutch AdjustmentMotion Control Linkage Adjustment Motion Control Damper AdjustmentMaintenance Motion Control Handle AdjustmentMotion Control Neutral Lock Pivot Adjustment Motion Control Full Forward Tracking AdjustmentCaster Pivot Bearings Pre-LoadAdjustment MaintenanceRH Motion Control Shown Clean Hydro Fan Cooling Guards CleaningClean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsMaintenance Battery DisposalWaste Disposal Motor Oil DisposalTroubleshooting TroubleshootingCorrective Action TroubleshootingProblem Possible CausePINK SchematicsSchematics Electrical DiagramLogic SchematicElectrical SchematicsSchematics Hydraulic DiagramGeneral Warranty Conditions and Products Covered Exmark Lazer Z and Lazer Z AS Turf Equipment3 Year Limited Commercial Warranty 5 Year or 750 Hours Limited Consumer WarrantyPage Page Description of Work Done Service RecordService Done By DatePage Page MID-MOUNTRIDING ACCESSORIES AND OPTIONS OUT-FRONTRIDING ACCESSORIES AND OPTIONSWALK-BEHINDACCESSORIES AND OPTIONS
Related manuals
Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.
Top Page Image Contents