Exmark 000 & higher, S/N 790 Stopping the Engine, Driving the Machine, Operation, Driving Forward

Page 24
Stopping the Engine

Operation

Stopping the Engine

1.Bring the unit to a full stop.

2.Disengage the PTO.

3.Move the motion control levers out to the neutral lock position.

4.Engage the parking brake.

5.Place the throttle midway between the “SLOW” and “FAST” positions.

6.Allow the engine to run for a minimum of 15 seconds, then turn the ignition switch to the “OFF” position to stop the engine.

7.Remove the key to prevent children or other unauthorized persons from starting engine.

8.Close the fuel shut-off valve, located behind and below the seat, when the machine will not be in use for a few days, when transporting, or when the unit is parked inside a building.

Driving the Machine

Driving the Machine CAUTION

Machine can spin very rapidly by positioning one lever too much ahead of the other. Operator may lose control of the machine, which may cause damage to the machine or injury.

•Use caution when making turns.

•Slow the machine down before making sharp turns.

Important: To begin movement (forward or backward) the operator must be in the seat, the brake lever must be disengaged (pushed down) before the motion control levers can be moved in or the engine will stop.

When the motion control levers are positioned fully outward (apart) in the T-slot, the drive system is in the neutral lock position (Figure 14).

Note: The “N” LCD indicator appears when both levers are in the neutral lock position.

When the motion control levers are moved directly inward (together) the drive system is in the neutral operate position.

Figure 14

1.

Neutral lock position

4.

Forward

 

(handles out)

 

 

2.

Neutral operate position

5.

Neutral (operate)

 

(handles in)

6.

Reverse

3.

Front of Unit

 

 

 

 

Driving Forward

1.Release the parking brake.

2.Move the motion control levers inward to the center to the neutral position.

3.To move forward in a straight line, move both levers forward with equal pressure.

To turn left or right, pull the motion control lever back toward neutral in the desired turn direction.

The machine will move faster the farther the motion control levers are moved from the neutral position.

4.To stop, position both motion control levers in the neutral operate position.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents LAZER Z MODELS For Serial Nos 790,000 & HigherPart No. 4500-471Rev. A CALIFORNIA Proposition 65 Warning Introduction Model No Serial NoContents Safety Safety Alert SymbolSafety Safe Operating PracticesDANGER SafetyDANGER Operation SafetyUsing the Rollover Protection System ROPS Slope OperationSafety Do Not mow slopes when grass is wetMaintenance and Storage SafetySafety and Instructional Decals SafetySafety 109-3148109-7232 107-2102 109-7330 107-2112Safety 109-8483109-9361 Deck Drive Belt RoutingSafety PTO Switch Symbols116-0211 Message DisplaySpecifications SpecificationsSafety Interlock System Model NumbersSeat Hydrostatic Ground Drive SystemTires & Wheels SpecificationsDimensions Cutting DeckOverall Width Overall LengthCurb Weight Accessory Weight Table WorksheetTread Width Center to Center of Tires, Widthwise SpecificationsProduct Overview Torque RequirementsProduct Overview Operation ControlsOperation Motion Control LeversIgnition Switch Hour MeterOperation PTO Engagement Switch Low Voltage IndicatorFuel Shut-OffValve Fuel GaugeOperating Instructions Pre-StartDeck Lift Pedal Transport LockOpen the Fuel Shut-OffValve Starting the EngineEngaging the PTO Disengaging the PTOStopping the Engine Driving the MachineUse caution when making turns OperationAdjusting the Cutting Height Adjusting the Anti-ScalpRollersOperation Driving in ReverseTransporting Transporting a UnitOperation Loading a Unit OperationMaintenance Recommended Maintenance SchedulesMaintenance Periodic Maintenance Check Battery ChargeService Interval Before each use or daily Service Interval As requiredCheck Safety Interlock System Check Mower BladesMaintenance Service Interval Before each use or dailyService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareService Interval After the first 5 hours Service Interval Every 50 hoursChange Engine Oil Check Hydraulic Oil LevelCheck Condition Of Belts Lubricate Grease FittingsLubricate Caster Wheel Hubs MaintenanceService Interval Every 200 hours Service Interval Every 100 hoursService Interval Every 500 hours Lubricate Brake Handle PivotWheel Hub - Slotted Nut Torque Specification Service Interval After the first 100 hoursCheck Spark Arrester if equipped Every 500 hours thereafterAdjustments Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseMaintenance 8.Raise the discharge deflectorDeck Removal MaintenanceAdjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension MaintenanceElectric Clutch Adjustment Motion Control Linkage AdjustmentMotion Control Damper Adjustment MaintenanceMotion Control Handle Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Full Forward Tracking Adjustment MaintenanceCaster Pivot Bearings Pre-LoadAdjustment MaintenanceRH Motion Control Shown Cleaning Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling GuardsBattery Disposal Waste DisposalMotor Oil Disposal MaintenanceTroubleshooting TroubleshootingTroubleshooting ProblemPossible Cause Corrective ActionSchematics SchematicsElectrical Diagram PINKSchematic ElectricalSchematics LogicHydraulic Diagram SchematicsExmark Lazer Z and Lazer Z AS Turf Equipment 3 Year Limited Commercial Warranty5 Year or 750 Hours Limited Consumer Warranty General Warranty Conditions and Products CoveredPage Page Service Record Service Done ByDate Description of Work DonePage Page MID-MOUNTRIDING ACCESSORIES AND OPTIONS OUT-FRONTRIDING ACCESSORIES AND OPTIONSWALK-BEHINDACCESSORIES AND OPTIONS
Related manuals
Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.
Top Page Image Contents