Exmark 000 & higher, 4500-471 Check Condition Of Belts, Lubricate Grease Fittings, Maintenance

Page 33
Check Condition Of Belts

Maintenance

Check Condition Of Belts

Service Interval: Every 50 hours

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Remove left and right belt shields on deck and lift up floor pan to inspect deck drive belt.

3.Check under machine to inspect the pump drive belt.

Note: No adjustments are required for belt tension.

Lubricate Grease Fittings

Note: See chart for service intervals.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lubricate fittings with one to two pumps of NGLI grade #2 multi-purpose gun grease.

Refer to the following chart for fitting locations and lubrication schedule.

Lubrication Chart

Fitting

Initial

Number of

Service

Locations

Pumps

Places

Interval

1. Deck and

1

2

Yearly

Pump Idler

 

 

 

Pivots

 

 

 

2. Front

*0

2

*Yearly

Caster

 

 

 

Pivots

 

 

 

*See step 3 for special lubrication instructions on the front caster pivots.

3.Lubricate front caster pivots once a year. Remove hex plug and cap. Thread grease zerk in hole and

pump with grease until it oozes out around top bearing. Remove grease zerk and thread plug back in. Place cap back on.

Lubricate Caster Wheel Hubs

Service Interval: As required

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

 

Figure 23

1. Seal guard

2. Spacer nut with wrench

 

flats

2.Remove caster wheel from caster forks.

3.Remove seal guards from the wheel hub.

4.Remove one of the spacer nuts from the axle assembly in the caster wheel. Note that thread locking adhesive has been applied to lock the spacer nuts to the axle. Remove the axle (with the other spacer nut still assembled to it) from the wheel assembly.

5.Pry out seals, and inspect bearings for wear or damage and replace if necessary.

6.Pack the bearings with a NGLI grade #1 multi-purpose grease.

7.Insert one bearing, one new seal into the wheel.

Note: Seals (Exmark P/N 103-0063) must be replaced.

8.If the axle assembly has had both spacer nuts removed (or broken loose), apply a thread locking adhesive to one spacer nut and thread onto the axle with the wrench flats facing outward. Do Not thread spacer nut all of the way onto the end of the axle. Leave approximately 1/8 inch (3 mm) from the outer surface of the spacer nut to the end of the axle inside the nut.

33

Image 33
Contents LAZER Z MODELS For Serial Nos 790,000 & HigherPart No. 4500-471Rev. A CALIFORNIA Proposition 65 Warning Model No Serial No IntroductionContents Safety Alert Symbol SafetySafety Safe Operating PracticesDANGER SafetyDANGER Safety OperationSlope Operation Using the Rollover Protection System ROPSSafety Do Not mow slopes when grass is wetSafety Maintenance and StorageSafety Safety and Instructional Decals109-3148 Safety109-7232 107-2102 109-7330 107-2112109-8483 Safety109-9361 Deck Drive Belt RoutingPTO Switch Symbols Safety116-0211 Message DisplaySpecifications SpecificationsSafety Interlock System Model NumbersHydrostatic Ground Drive System SeatTires & Wheels SpecificationsCutting Deck DimensionsOverall Width Overall LengthAccessory Weight Table Worksheet Curb WeightTread Width Center to Center of Tires, Widthwise SpecificationsProduct Overview Torque RequirementsProduct Overview Controls OperationOperation Motion Control LeversIgnition Switch Hour MeterOperation Low Voltage Indicator PTO Engagement SwitchFuel Shut-OffValve Fuel GaugePre-Start Operating InstructionsDeck Lift Pedal Transport LockStarting the Engine Open the Fuel Shut-OffValveEngaging the PTO Disengaging the PTODriving the Machine Stopping the EngineUse caution when making turns OperationAdjusting the Anti-ScalpRollers Adjusting the Cutting HeightOperation Driving in ReverseTransporting Transporting a UnitOperation Operation Loading a UnitMaintenance Recommended Maintenance SchedulesMaintenance Check Battery Charge Periodic MaintenanceService Interval Before each use or daily Service Interval As requiredCheck Mower Blades Check Safety Interlock SystemMaintenance Service Interval Before each use or dailyCheck Rollover Protections Systems Roll Bar Knobs Service Air CleanerCheck Seat Belt Check for Loose HardwareService Interval Every 50 hours Service Interval After the first 5 hoursChange Engine Oil Check Hydraulic Oil LevelLubricate Grease Fittings Check Condition Of BeltsLubricate Caster Wheel Hubs MaintenanceService Interval Every 100 hours Service Interval Every 200 hoursService Interval Every 500 hours Lubricate Brake Handle PivotService Interval After the first 100 hours Wheel Hub - Slotted Nut Torque SpecificationCheck Spark Arrester if equipped Every 500 hours thereafterThread Locking Adhesives AdjustmentsCopper-Based Anti-seize Dielectric Grease8.Raise the discharge deflector MaintenanceMaintenance Deck RemovalPump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension MaintenanceMotion Control Linkage Adjustment Electric Clutch AdjustmentMotion Control Damper Adjustment MaintenanceMotion Control Neutral Lock Pivot Adjustment Motion Control Handle AdjustmentMotion Control Full Forward Tracking Adjustment MaintenanceCaster Pivot Bearings Pre-LoadAdjustment MaintenanceRH Motion Control Shown Clean Engine and Exhaust System Area CleaningRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling GuardsWaste Disposal Battery DisposalMotor Oil Disposal MaintenanceTroubleshooting TroubleshootingProblem TroubleshootingPossible Cause Corrective ActionSchematics SchematicsElectrical Diagram PINKElectrical SchematicSchematics LogicSchematics Hydraulic Diagram3 Year Limited Commercial Warranty Exmark Lazer Z and Lazer Z AS Turf Equipment5 Year or 750 Hours Limited Consumer Warranty General Warranty Conditions and Products CoveredPage Page Service Done By Service RecordDate Description of Work DonePage Page MID-MOUNTRIDING ACCESSORIES AND OPTIONS OUT-FRONTRIDING ACCESSORIES AND OPTIONSWALK-BEHINDACCESSORIES AND OPTIONS
Related manuals
Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.