Exmark 000 & higher, 4500-471, S/N 790 manual Danger, Safety

Page 6
 DANGER

Safety

Manual background DANGER

In certain conditions gasoline is extremely flammable and vapors are explosive.

A fire or explosion from gasoline can burn you, others, and cause property damage.

Fill the fuel tank outdoors in an open area, when the engine is cold. Wipe up any gasoline that spills.

Never refill the fuel tank or drain the machine indoors or inside an enclosed trailer.

Do Not fill the fuel tank completely full. Add gasoline to the fuel tank until the level is 1/4 to 1/2 inch (6–13 mm) below the bottom of the filler neck. This empty space in the tank allows gasoline to expand.

Never smoke when handling gasoline, and stay away from an open flame or where gasoline fumes may be ignited by spark.

Store gasoline in an approved container and keep it out of the reach of children.

Add fuel before starting the engine. Never remove the cap of the fuel tank or add fuel when engine is running or when the engine is hot.

If fuel is spilled, Do Not attempt to start the engine. Move away from the area of the spill and avoid creating any source of ignition until fuel vapors have dissipated.

Do Not operate without entire exhaust system in place and in proper working condition.

Manual background DANGER

In certain conditions during fueling, static electricity can be released causing a spark which can ignite gasoline vapors. A fire or explosion from gasoline can burn you and others and cause property damage.

Always place gasoline containers on the ground away from your vehicle before filling.

Do Not fill gasoline containers inside a vehicle or on a truck or trailer bed because interior carpets or plastic truck bed liners may insulate the container and slow the loss of any static charge.

When practical, remove gas-powered equipment from the truck or trailer and refuel the equipment with its wheels on the ground.

If this is not possible, then refuel such equipment on a truck or trailer from a portable container, rather than from a gasoline dispenser nozzle.

If a gasoline dispenser nozzle must be used, keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete.

Manual background WARNING

Gasoline is harmful or fatal if swallowed. Long-term exposure to vapors has caused cancer in laboratory animals. Failure to use caution may cause serious injury or illness.

Avoid prolonged breathing of vapors.

Keep face away from nozzle and gas tank/container opening.

Keep away from eyes and skin.

Never siphon by mouth.

6

Image 6
Contents LAZER Z MODELS For Serial Nos 790,000 & HigherPart No. 4500-471Rev. A CALIFORNIA Proposition 65 Warning Introduction Model No Serial NoContents Safety SafetySafety Alert Symbol Safe Operating PracticesDANGER SafetyDANGER Operation SafetySafety Using the Rollover Protection System ROPSSlope Operation Do Not mow slopes when grass is wetMaintenance and Storage SafetySafety and Instructional Decals Safety109-7232 Safety109-3148 107-2102 109-7330 107-2112109-9361 Safety109-8483 Deck Drive Belt Routing116-0211 SafetyPTO Switch Symbols Message DisplaySafety Interlock System SpecificationsSpecifications Model NumbersTires & Wheels SeatHydrostatic Ground Drive System SpecificationsOverall Width DimensionsCutting Deck Overall LengthTread Width Center to Center of Tires, Widthwise Curb WeightAccessory Weight Table Worksheet SpecificationsProduct Overview Torque RequirementsProduct Overview Operation OperationControls Motion Control LeversIgnition Switch Hour MeterOperation Fuel Shut-OffValve PTO Engagement SwitchLow Voltage Indicator Fuel GaugeDeck Lift Pedal Operating InstructionsPre-Start Transport LockEngaging the PTO Open the Fuel Shut-OffValveStarting the Engine Disengaging the PTOUse caution when making turns Stopping the EngineDriving the Machine OperationOperation Adjusting the Cutting HeightAdjusting the Anti-ScalpRollers Driving in ReverseTransporting Transporting a UnitOperation Loading a Unit OperationMaintenance Recommended Maintenance SchedulesMaintenance Service Interval Before each use or daily Periodic MaintenanceCheck Battery Charge Service Interval As requiredMaintenance Check Safety Interlock SystemCheck Mower Blades Service Interval Before each use or dailyCheck Seat Belt Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check for Loose HardwareChange Engine Oil Service Interval After the first 5 hoursService Interval Every 50 hours Check Hydraulic Oil LevelLubricate Caster Wheel Hubs Check Condition Of BeltsLubricate Grease Fittings MaintenanceService Interval Every 500 hours Service Interval Every 200 hoursService Interval Every 100 hours Lubricate Brake Handle PivotCheck Spark Arrester if equipped Wheel Hub - Slotted Nut Torque SpecificationService Interval After the first 100 hours Every 500 hours thereafterCopper-Based Anti-seize AdjustmentsThread Locking Adhesives Dielectric GreaseMaintenance 8.Raise the discharge deflectorDeck Removal MaintenanceDeck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension MaintenanceMotion Control Damper Adjustment Electric Clutch AdjustmentMotion Control Linkage Adjustment MaintenanceMotion Control Full Forward Tracking Adjustment Motion Control Handle AdjustmentMotion Control Neutral Lock Pivot Adjustment MaintenanceCaster Pivot Bearings Pre-LoadAdjustment MaintenanceRH Motion Control Shown Remove Engine Shrouds and Clean Cooling Fins CleaningClean Engine and Exhaust System Area Clean Hydro Fan Cooling GuardsMotor Oil Disposal Battery DisposalWaste Disposal MaintenanceTroubleshooting TroubleshootingPossible Cause TroubleshootingProblem Corrective ActionElectrical Diagram SchematicsSchematics PINKSchematics SchematicElectrical LogicHydraulic Diagram Schematics5 Year or 750 Hours Limited Consumer Warranty Exmark Lazer Z and Lazer Z AS Turf Equipment3 Year Limited Commercial Warranty General Warranty Conditions and Products CoveredPage Page Date Service RecordService Done By Description of Work DonePage Page MID-MOUNTRIDING ACCESSORIES AND OPTIONS OUT-FRONTRIDING ACCESSORIES AND OPTIONSWALK-BEHINDACCESSORIES AND OPTIONS
Related manuals
Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.