Exmark S/N 790, 000 & higher, 4500-471 manual Ignition Switch, Hour Meter, Operation

Page 20
Ignition Switch

Operation

Note: The LCD indicator appears in the message display on the RH console when the park brake is engaged (see Figure 9).

Pull the lever up and rearward to engage the brake.

Depress the release button and push downward to disengage the brake.

Figure 7

1. Release button

2. Park brake

 

 

The unit must be tied down and brake engaged when transporting.

Ignition Switch

Located on right console (see Figure 6).

The ignition switch is used to start and stop the engine. The switch has three positions “OFF”, “ON” and “START”. Insert key into switch and rotate clockwise to the “ON” position. Rotate clockwise to the next position to engage the starter (key must be held against spring pressure in this position). Allow the key to return to the “on” position immediately after the engine starts.

Figure 8

1. Off

3. Start

2.On

Note: Brake must be engaged, motion control levers out (neutral lock position) and PTO switch

disengaged to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

Hour Meter

Located on the right console in the message display (see Figure 6 and Figure 9).

The hour meter records the number of hours that the engine has run.

Figure 9

1.LCD Indicators

2.Low fuel indicator light

3.Fuel level bar display

4.Low voltage indicator light

5.Hour/Voltage display

Hours are recorded when the key is on and the engine is running (battery voltage is 12.8V or higher) or when the key is on and the operator is in the seat.

The hour meter is recording when the decimal point is flashing in Hour/Voltage display.

Hours are displayed when the key is off and when the machine is running.

Note: If the ignition key is turned to the “ON” position for a few seconds before cranking the engine, the battery voltage will display in the area where the hours are normally displayed.

Note: The LCD indicators appear when each control meets the “safe to start” mode (e.g. the indicator turns on when the operator is in the seat.)

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Part No. 4500-471Rev. A LAZER Z MODELSFor Serial Nos 790,000 & Higher CALIFORNIA Proposition 65 Warning Introduction Model No Serial NoContents Safety Safety Alert SymbolSafety Safe Operating PracticesDANGER DANGERSafety Operation SafetyUsing the Rollover Protection System ROPS Slope OperationSafety Do Not mow slopes when grass is wetMaintenance and Storage SafetySafety and Instructional Decals SafetySafety 109-3148109-7232 107-2102 109-7330 107-2112Safety 109-8483109-9361 Deck Drive Belt RoutingSafety PTO Switch Symbols116-0211 Message DisplaySpecifications SpecificationsSafety Interlock System Model NumbersSeat Hydrostatic Ground Drive SystemTires & Wheels SpecificationsDimensions Cutting DeckOverall Width Overall LengthCurb Weight Accessory Weight Table WorksheetTread Width Center to Center of Tires, Widthwise SpecificationsProduct Overview Product OverviewTorque Requirements Operation ControlsOperation Motion Control LeversOperation Ignition SwitchHour Meter PTO Engagement Switch Low Voltage IndicatorFuel Shut-OffValve Fuel GaugeOperating Instructions Pre-StartDeck Lift Pedal Transport LockOpen the Fuel Shut-OffValve Starting the EngineEngaging the PTO Disengaging the PTOStopping the Engine Driving the MachineUse caution when making turns OperationAdjusting the Cutting Height Adjusting the Anti-ScalpRollersOperation Driving in ReverseOperation TransportingTransporting a Unit Loading a Unit OperationMaintenance MaintenanceRecommended Maintenance Schedules Periodic Maintenance Check Battery ChargeService Interval Before each use or daily Service Interval As requiredCheck Safety Interlock System Check Mower BladesMaintenance Service Interval Before each use or dailyService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareService Interval After the first 5 hours Service Interval Every 50 hoursChange Engine Oil Check Hydraulic Oil LevelCheck Condition Of Belts Lubricate Grease FittingsLubricate Caster Wheel Hubs MaintenanceService Interval Every 200 hours Service Interval Every 100 hoursService Interval Every 500 hours Lubricate Brake Handle PivotWheel Hub - Slotted Nut Torque Specification Service Interval After the first 100 hoursCheck Spark Arrester if equipped Every 500 hours thereafterAdjustments Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseMaintenance 8.Raise the discharge deflectorDeck Removal MaintenanceAdjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension MaintenanceElectric Clutch Adjustment Motion Control Linkage AdjustmentMotion Control Damper Adjustment MaintenanceMotion Control Handle Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Full Forward Tracking Adjustment MaintenanceRH Motion Control Shown Caster Pivot Bearings Pre-LoadAdjustmentMaintenance Cleaning Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling GuardsBattery Disposal Waste DisposalMotor Oil Disposal MaintenanceTroubleshooting TroubleshootingTroubleshooting ProblemPossible Cause Corrective ActionSchematics SchematicsElectrical Diagram PINKSchematic ElectricalSchematics LogicHydraulic Diagram SchematicsExmark Lazer Z and Lazer Z AS Turf Equipment 3 Year Limited Commercial Warranty5 Year or 750 Hours Limited Consumer Warranty General Warranty Conditions and Products CoveredPage Page Service Record Service Done ByDate Description of Work DonePage Page WALK-BEHINDACCESSORIES AND OPTIONS MID-MOUNTRIDING ACCESSORIES AND OPTIONSOUT-FRONTRIDING ACCESSORIES AND OPTIONS
Related manuals
Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.
Top Page Image Contents