Exmark 4500-471, S/N 790 Dimensions, Cutting Deck, Overall Width, Overall Length, Overall Height

Page 16
Cutting Deck

Specifications

Cutting Deck

Cutting Width:

48 inch Deck: (121.9 cm)

52 inch Deck: (132.1 cm)

60 inch Deck: (152.4 cm)

72 inch Deck: (182.9 cm)

Discharge: Side

Blade Size: (3 ea.)

48 inch Deck: 16.25 inches (41.3 cm)

52 inch Deck: 18.00 inches (45.7 cm)

60 inch Deck: 20.50 inches (52.1 cm)

72 inch Deck: 24.50 inches (62.2 cm)

Blade Spindles: Solid steel spindles with 1.18 inch (30 mm) I.D. bearings.

Deck Drive:

Electric clutch. Shaft diameter 1.125 inches (2.86 cm)

48 and 52 inch Decks: “B” Section belt with self-tensioning idler.

60 and 72 inch Decks: 5V Section belt with self-tensioning idler.

Deck:

Full floating deck is attached to out-front support frame. Anti-scalp rollers provide maximum turf protection. Deck design allows for bagging, mulching or side discharge.

48 inch Deck: 3 anti-scalp rollers

52 inch Deck: 3 anti-scalp rollers

60 inch Deck: 4 anti-scalp rollers

72 inch Deck: 4 anti-scalp rollers

Deck Depth:

48 inch Deck: 5.5 inches (14 cm)

52 inch Deck: 5.5 inches (14 cm)

60 inch Deck: 5.5 inches (14 cm)

72 inch Deck: 5.5 inches (14 cm)

Cutting Height Adjustment:

Foot activated lever is used to adjust the cutting height from 1 inch (2.5 cm) to 5 1/2 inches (14 cm) in 1/4 inch (6.4 mm) increments.

Mulching Kit: Optional.

Dimensions

Overall Width:

 

48 inch Deck

52 inch Deck

Without Deck

45.7

inches

45.7

inches

 

(116.1 cm)

(116.1 cm)

Deflector Up

51.8

inches

56.3

inches

 

(131.6 cm)

(143.0 cm)

Deflector Down

59.6

inches

64.8

inches

 

(151.4 cm)

(164.6 cm)

 

60 inch Deck

72 inch Deck

Without Deck

53.0

inches

59.1

inches

 

(134.6 cm)

(150.1 cm)

Deflector Up

62.5

inches

73.5

inches

 

(158.8 cm)

(186.7 cm)

Deflector Down

72.8

inches

84.9

inches

 

(184.9 cm)

(215.6 cm)

Overall Length:

 

48 inch Deck

52 inch Deck

Roll Bar - Up

79.2

inches

79.2

inches

 

(201.2 cm)

(201.2 cm)

Roll Bar - Down

80.9

inches

80.9

inches

 

(205.5 cm)

(205.5 cm)

 

60 inch Deck

72 inch Deck

Roll Bar - Up

83.1

inches

86.1

inches

 

(211.1 cm)

(218.7 cm)

Roll Bar - Down

84.8

inches

87.8

inches

 

(215.4 cm)

(223.0 cm)

Overall Height:

Roll Bar - Up

Roll Bar - Down

70.5 inches (179.1 cm)

46.8 inches (118.9 cm)

16

Image 16
Contents For Serial Nos 790,000 & Higher LAZER Z MODELSPart No. 4500-471Rev. A CALIFORNIA Proposition 65 Warning Introduction Model No Serial NoContents Safety Safety Alert SymbolSafety Safe Operating PracticesSafety DANGERDANGER Operation SafetyUsing the Rollover Protection System ROPS Slope OperationSafety Do Not mow slopes when grass is wetMaintenance and Storage SafetySafety and Instructional Decals SafetySafety 109-3148109-7232 107-2102 109-7330 107-2112Safety 109-8483109-9361 Deck Drive Belt RoutingSafety PTO Switch Symbols116-0211 Message DisplaySpecifications SpecificationsSafety Interlock System Model NumbersSeat Hydrostatic Ground Drive SystemTires & Wheels SpecificationsDimensions Cutting DeckOverall Width Overall LengthCurb Weight Accessory Weight Table WorksheetTread Width Center to Center of Tires, Widthwise SpecificationsTorque Requirements Product OverviewProduct Overview Operation ControlsOperation Motion Control LeversHour Meter Ignition SwitchOperation PTO Engagement Switch Low Voltage IndicatorFuel Shut-OffValve Fuel GaugeOperating Instructions Pre-StartDeck Lift Pedal Transport LockOpen the Fuel Shut-OffValve Starting the EngineEngaging the PTO Disengaging the PTOStopping the Engine Driving the MachineUse caution when making turns OperationAdjusting the Cutting Height Adjusting the Anti-ScalpRollersOperation Driving in ReverseTransporting a Unit TransportingOperation Loading a Unit OperationRecommended Maintenance Schedules MaintenanceMaintenance Periodic Maintenance Check Battery ChargeService Interval Before each use or daily Service Interval As requiredCheck Safety Interlock System Check Mower BladesMaintenance Service Interval Before each use or dailyService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareService Interval After the first 5 hours Service Interval Every 50 hoursChange Engine Oil Check Hydraulic Oil LevelCheck Condition Of Belts Lubricate Grease FittingsLubricate Caster Wheel Hubs MaintenanceService Interval Every 200 hours Service Interval Every 100 hoursService Interval Every 500 hours Lubricate Brake Handle PivotWheel Hub - Slotted Nut Torque Specification Service Interval After the first 100 hoursCheck Spark Arrester if equipped Every 500 hours thereafterAdjustments Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseMaintenance 8.Raise the discharge deflectorDeck Removal MaintenanceAdjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension MaintenanceElectric Clutch Adjustment Motion Control Linkage AdjustmentMotion Control Damper Adjustment MaintenanceMotion Control Handle Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Full Forward Tracking Adjustment MaintenanceMaintenance Caster Pivot Bearings Pre-LoadAdjustmentRH Motion Control Shown Cleaning Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling GuardsBattery Disposal Waste DisposalMotor Oil Disposal MaintenanceTroubleshooting TroubleshootingTroubleshooting ProblemPossible Cause Corrective ActionSchematics SchematicsElectrical Diagram PINKSchematic ElectricalSchematics LogicHydraulic Diagram SchematicsExmark Lazer Z and Lazer Z AS Turf Equipment 3 Year Limited Commercial Warranty5 Year or 750 Hours Limited Consumer Warranty General Warranty Conditions and Products CoveredPage Page Service Record Service Done ByDate Description of Work DonePage Page OUT-FRONTRIDING ACCESSORIES AND OPTIONS MID-MOUNTRIDING ACCESSORIES AND OPTIONSWALK-BEHINDACCESSORIES AND OPTIONS
Related manuals
Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.