Exmark 920 manual Engaging the PTO, Disengaging the PTO, Stopping the Engine

Page 24

Operation

7.Turn ignition switch to the “ON” position. Depress the glow plug switch and the glow plug light will turn on. Hold switch as required by chart below. Turn the ignition switch to the “START” position. Release the ignition switch as soon as the engine starts.

Glow Plug Chart

Ambient Temperature

Hold Glow Plugs On

Above 50°F (10°C)

NO NEED

50°F (10°C) to 23°F (-5°C)

Approximately 5 seconds

Below 23°F (-5°C)

Approximately 10 seconds

 

 

Limit of continuous use

20 seconds

 

 

The glow plug light, located near the glow plug switch, will illuminate when the switch is depressed. The glow plug light indicates the glow plugs are preheating the combustion chamber.

Important: Do Not crank the engine continuously for more then ten seconds at a time. If the engine does not start, allow a 30 second cool-down period between starting attempts. Failure to follow these guidelines can burn out the starter motor and/or fuel solenoid.

8.Move the throttle to the “SLOW” (if in “MIDWAY”) and let the engine warm up a few minutes before moving the throttle to the “FAST” position.

Engaging the PTO

DANGER

The rotating blades under the mower deck are dangerous. Blade contact can cause serious injury or kill you.

Do Not put hands or feet under the mower or mower deck when the blades are engaged.

DANGER

An uncovered discharge opening will allow objects to be thrown in an operator’s or bystander’s direction. Also, contact with the blade could occur. Thrown objects or blade contact can cause serious injury or death.

Never operate the mower with the discharge deflector raised, removed, or altered unless there is a grass collection system or mulch kit in place and working properly.

The PTO push-pull switch engages the cutting blades. Be sure that all persons are clear of the mower deck and discharge area before engaging PTO.

Important: Operator must be in seat before the PTO can be engaged.

1.Set the throttle midway between the “SLOW” and “FAST” positions.

2.Pull the PTO switch outward to engage the blades.

3.Place the throttle in the “FAST” position to begin mowing.

Disengaging the PTO

1.Set the throttle midway between the “SLOW” and “FAST” positions.

2.Push the PTO switch in to disengage the blades.

Stopping the Engine

1.Bring the unit to a full stop.

2.Move the motion control levers out to the neutral lock position.

3.Engage the parking brake.

4.Place the throttle midway between the “SLOW” and “FAST” positions.

5.Disengage the PTO.

6.Allow the engine to run for a minimum of 15 seconds, then turn the ignition switch to the “OFF” position to stop the engine.

7.Remove the key to prevent children or other unauthorized persons from starting engine.

8.Close the fuel shut-off valve when the machine will not be in use for a few days, when transporting, or when the unit is parked inside a building.

24

Image 24
Contents Lazer Z D-SERIES California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingOperation Slope Operation Using the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Specifications Model NumbersSystems Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Torque RequirementsProduct Overview OperationControls Motion Control LeversIgnition Switch Tracking Adjustment KnobBrake Lever Hour MeterPre-Start Operating Instructions Biodiesel ReadyRaise the Rollover Protection System Rops Open the Fuel Shut-Off ValveEngaging the PTO Disengaging the PTOStopping the Engine Adjusting the Cutting Height Driving the MachineAdjusting the Anti-Scalp Rollers Transporting Transporting a UnitLoading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Service Interval As requiredCheck Mower Blades Engine Block of the StalledCheck Safety Interlock System Check Rollover Protections Systems Roll Bar PinsService Air Cleaner Check Seat BeltChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of Belts Lubricate Grease FittingsWheel Hub Slotted Nut Torque Specification Lubricate Caster Wheel HubsLubricate Brake Handle Pivot Lubricate Brake Rod BushingsLubricate Motion Control Bronze Bushings Check Spark PlugsDrain Fuel Filter/Water Separator Change Fuel Filter/Water SeparatorCheck Engine Coolant Level Change Engine CoolantCheck Spark Arrester if equipped Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Copper-Based Anti-seizeDielectric Grease Deck LevelingMule Drive Belt Tension Adjustment Pump Drive Belt TensionDeck Belt Tension Belt Guide Adjustment Brake Link AdjustmentAlternator Belt Tension Electric Clutch Adjustment Brake AdjustmentReverse Indicator Adjustment Motion Control Linkage Adjustment Motion Control Damper Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean Engine Cooling System Clean Engine and Exhaust System AreaClean Debris From Machine Clean Grass Build-Up Under DeckClean the Radiator Waste DisposalBattery Disposal Troubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Schematics Electrical DiagramElectrical Schematic Exmark Commercial Turf Equipment Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 64 pages 1.01 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 64 pages 37.72 Kb Manual 52 pages 8.82 Kb

0, 920 specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.