Exmark 920 manual Check Condition Of Belts, Lubricate Grease Fittings

Page 34

Maintenance

2.Check tire pressure in drive tires.

3.Inflate drive tires to 10 psi (69 kPa).

4.Semi-pneumatic caster tires do not need to be inflated.

Note: Do Not add any type of tire liner or foam fill material to the tires. Excessive loads created by foam filled tires may cause failures to the hydro drive system, frame, and other components. Foam filling tires will void the warranty.

Check Condition Of Belts

Service Interval: Every 40 hours

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Unhook seat latch and tilt seat up. Remove the air detector panel on front side of the engine compartment to check pump drive belt and alternator belt.

3.Remove left and right belt shields on deck and lift up floor pan to inspect deck drive belt.

4.Check under machine to inspect the mule drive belt. Refer to Mule Drive Belt Tension Adjustment section in Adjustments.

Lubricate Grease Fittings

Note: See chart for service intervals.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lubricate fittings with one to two pumps of NGLI grade #2 multi-purpose gun grease.

Refer to the following chart for fitting locations and lubrication schedule.

Lubrication Chart

Fitting

Initial

Number of

Service

Locations

Pumps

Places

Interval

1. Front

*0

2

*Yearly

Caster wheel

 

 

 

hubs

 

 

 

2. Front

*0

2

*Yearly

Caster

 

 

 

Pivots

 

 

 

3. Height

1

5

40 Hours

Adjustment

 

 

 

Shaft

 

 

 

Bearings

 

 

 

Lubrication Chart

Fitting

Initial

Number of

Service

Locations

Pumps

Places

Interval

4. Deck

1

1

Yearly

Drive Belt

 

 

 

Idler Arm

 

 

 

5. Brake

1

2

200 Hours

Brackets

 

 

 

6. Mule

1

1

Yearly

Drive Belt

 

 

 

Idler Arm

 

 

 

7. Pump

1

1

Yearly

Drive Belt

 

 

 

Idler Arm

 

 

 

8. Deck

1

2

40 Hours

Rear Struts

 

 

 

*See step 3 for special lubrication instructions on the front caster pivots and the Lubricate Caster Wheel Hubs section for special lubrication instructions on the front casters wheel hubs.

Number 6 (Mule Drive Belt Idler Arm) Located

Under Engine Frame

Number 7 (Pump Drive Belt Idler Arm) Located

Under Engine Frame

3.Lubricate front caster pivots once a year. Remove hex plug and cap. Thread grease zerk in hole and pump with grease until it oozes out around top bearing. Remove grease zerk and thread plug back in. Place cap back on.

34

Image 34
Contents Lazer Z D-SERIES California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingOperation Slope Operation Using the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Model Numbers SpecificationsSystems Tires & Wheels SeatHydrostatic Ground Drive System Cutting DeckDimensions Torque RequirementsControls Product OverviewOperation Motion Control LeversBrake Lever Ignition SwitchTracking Adjustment Knob Hour MeterPre-Start Raise the Rollover Protection System Rops Operating InstructionsBiodiesel Ready Open the Fuel Shut-Off ValveDisengaging the PTO Engaging the PTOStopping the Engine Adjusting the Cutting Height Driving the MachineAdjusting the Anti-Scalp Rollers Transporting a Unit TransportingLoading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Service Interval As requiredCheck Mower Blades Engine Block of the StalledService Air Cleaner Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Pins Check Seat BeltCheck Hydraulic Oil Level Change Engine OilCheck Tire Pressures Check Condition Of Belts Lubricate Grease FittingsLubricate Brake Handle Pivot Wheel Hub Slotted Nut Torque SpecificationLubricate Caster Wheel Hubs Lubricate Brake Rod BushingsDrain Fuel Filter/Water Separator Lubricate Motion Control Bronze BushingsCheck Spark Plugs Change Fuel Filter/Water SeparatorCheck Engine Coolant Level Change Engine CoolantCheck Spark Arrester if equipped Thread Locking AdhesivesDielectric Grease Mobil HTS Grease Or Food-Grade Anti-seizeCopper-Based Anti-seize Deck LevelingPump Drive Belt Tension Mule Drive Belt Tension AdjustmentDeck Belt Tension Brake Link Adjustment Belt Guide AdjustmentAlternator Belt Tension Electric Clutch Adjustment Brake AdjustmentReverse Indicator Adjustment Motion Control Linkage Adjustment Motion Control Damper Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean Engine Cooling System Clean Engine and Exhaust System AreaClean the Radiator Clean Debris From MachineClean Grass Build-Up Under Deck Waste DisposalBattery Disposal Troubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Schematics Electrical DiagramElectrical Schematic Exmark Commercial Turf Equipment Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 64 pages 1.01 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 64 pages 37.72 Kb Manual 52 pages 8.82 Kb

0, 920 specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.