Husqvarna 445e TrioBrake manual Cutting equipment, General rules

Page 11

GENERAL SAFETY PRECAUTIONS

Cutting equipment

This section describes how to choose and maintain your cutting equipment in order to:

•Reduce the risk of kickback.

•Reduce the risk of the saw chain breaking or jumping off the bar.

•Obtain optimal cutting performance.

•Extend the life of cutting equipment.

•Avoid increasing vibration levels.

General rules

•Only use cutting equipment recommended by us! See instructions under the heading Technical data.

•Keep the chain’s cutting teeth properly sharpened! Follow our instructions and use the recommended file gauge. A damaged or badly sharpened chain increases the risk of accidents.

•Maintain the correct depth gauge setting! Follow our instructions and use the recommended depth gauge clearance. Too large a clearance increases the risk of kickback.

•Keep the chain properly tensioned! If the chain is slack it is more likely to jump off and lead to increased wear on the bar, chain and drive sprocket.

•Keep cutting equipment well lubricated and properly maintained! A poorly lubricated chain is more likely to break and lead to increased wear on the bar, chain and drive sprocket.

Cutting equipment designed to reduce kickback

WARNING! Faulty cutting equipment or ! the wrong combination of bar and saw

chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data.

The only way to avoid kickback is to make sure that the kickback zone of the bar never touches anything.

By using cutting equipment with ”built-in” kickback reduction and keeping the chain sharp and well- maintained you can reduce the effects of kickback.

Bar

The smaller the tip radius the lower the chance of kickback.

Chain

A chain is made up of a number of links, which are available in standard and low-kickback versions.

IMPORTANT! No saw chain design eliminates the danger of kickback.

WARNING! Any contact with a rotating ! saw chain can cause extremely serious

injuries.

Some terms that describe the bar and chain

To maintain the safety features of the cutting equipment, you should replace a worn or damaged bar or chain with a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical Data for a list of replacement bar and chain combinations we recommend.

Bar

•Length (inches/cm)

•Number of teeth on bar tip sprocket (T).

•Chain pitch (inches). The spacing between the drive links of the chain must match the spacing of the teeth on the bar tip sprocket and drive sprocket.

English – 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 445e TrioBrake You will find the following labels on your chain saw KEY to SymbolsSymbols on the machine Symbols in the operator’s manualContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Chain catcher Throttle lockoutMuffler Stop switchRight hand guard Vibration damping systemCutting equipment designed to reduce kickback Cutting equipmentGeneral rules General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Filling with chain oil Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Checking wear on cutting equipment Checking chain lubricationChain drive sprocket Needle bearing lubricationBar Working with the chain AssemblyFitting the bar and chain Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageStarting Starting and StoppingStarting and stopping Stopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueSafe distance Tree felling techniqueLimbing Directional cuts Felling directionClearing the trunk and preparing your retreat Felling cut Freeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs General MaintenanceCarburetor adjustment Checking the brake trigger Checking the inertia brake releaseThrottle lockout Replacing the starter cord MufflerStarter Recoil spring a Tensioning the recoil springReplacing the return and drive springs Fitting the starterNeedle bearing lubrication Air filterSpark plug Lubricating the bar tip sprocketWinter use Air Injection centrifugal cleaningTemperature -5C 23F or colder Cooling systemDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data058/1,5 mm Bar and chain combinationsSaw chain filing and file gauges 050/1,3 mmYour Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsEtiquetas que se encuentran en la motosierra Aclaracion DE LOS SimbolosSímbolos en la máquina Símbolos en el manual de instruccionesPrecauciones de seguridad para usuarios de IndiceÍndice Apreciado cliente Introduccion¿Qué es qué en la motosierra? ¿QUE ES QUE?Importante Instrucciones Generales DE SeguridadMedidas a tomar antes de utilizar una motosierra nueva Freno de cadena con protección contra reculadas Emplee siempre el sentido comúnEquipo de protección personal Equipo de seguridad de la máquinaInstrucciones Generales DE Seguridad Captor de cadena Fiador del aceleradorSilenciador Protección de la mano derechaSistema amortiguador de vibraciones Botón de paradaEspada Equipo de corteReglas básicas Equipo de corte reductor de reculadasGeneralidades sobre el afilado de los dientes cortantes Expresiones características de la espada y cadenaGeneralidades sobre el ajuste de la profundidad de corte Tensado de la cadena Control de la lubricación de la cadena Lubricación del equipo de corteRepostaje de aceite para cadena de motosierra ¡ATENCION! La mayoría de los Piñón de arrastre de la cadenaLubricación del cojinete de agujas Control del desgaste del equipo de corteDeben utilizarse guantes protectores MontajeMontaje de la espada y la cadena ¡ATENCION! Para manipular la cadenaCarburante Manipulacion DEL CombustibleAlmacenamiento prolongado RepostajeSeguridad en el uso del combustible Transporte y almacenamientoArranque Arranque Y ParadaArranque y parada Parada Reglas básicas de seguridad Tecnica DE TrabajoAntes de utilizar la máquina Instrucciones generales de trabajoReglas básicas Designaciones Técnica básica de corteDistancia de seguridad Técnica de talaDesramado Corte de indicación Dirección de derriboCorte de ramas bajas y camino de retirada Corte de derribo ¿Qué es la reculada? Medidas preventivas de las reculadasTratamiento de una tala fallida Tronzado del tronco Ajuste del carburador MantenimientoGeneralidades Detenerse inmediatamente Control de la función de inerciaControl del efecto de frenado Fiador del acelerador Cambio del cordón de arranque SilenciadorMecanismo de arranque Muelle de retorno a Tensado del muelle de retornoCambio del muelle de retorno y el muelle de arrastre Montaje del mecanismo de arranqueLubricación del cojinete de agujas Filtro de aireBujía Engrase del cabezal de rueda de la espadaTemperaturas de -5C 23F o inferiores Sistema refrigeranteDepuración centrífuga Air Injection Utilización en inviernoPrograma de mantenimiento Datos técnicos Datos TecnicosAfilado y calibres de afilado de la cadena de sierra Combinaciones de espada y cadenaSUS Derechos Y Obligaciones DE Garantia Garantia DEL Sistema DE Control DE EmisionesOtras precauciones de seguridad Precauciones DE Seguridad DE LA Norma AmericanaPrecauciones de seguridad para usuarios de motosierras Precauciones de seguridad en reculadas´z+S23¶6X¨ Page 1151181-96
Top Page Image Contents