Husqvarna 445e TrioBrake manual General Safety Precautions, Before using a new chain saw

Page 6

GENERAL SAFETY PRECAUTIONS

Before using a new chain saw

Please read this manual carefully.

Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly.

Refuel and start the chain saw. See the instructions under the headings Fuel Handling and Starting and Stopping.

Do not use the chain saw until sufficient chain oil has reached the chain. See instructions under the heading Cutting equipment.

Long-term exposure to noise can result in permanent hearing impairment. So always use approved hearing protection.

WARNING! Under no circumstances may ! the design of the machine be modified

without the permission of the manufacturer. Always use genuine accessories. Non-authorized modifications and/or accessories can result in serious personal injury or the death of the operator or others. Your warranty may not cover damage or liability caused by the use of non- authorized accessories or replacement parts.

WARNING! A chain saw is a dangerous ! tool if used carelessly or incorrectly and

can cause serious, even fatal injuries. It is very important that you read and understand the contents of this operator’s manual.

WARNING! The inside of the muffler ! contain chemicals that may be

carcinogenic. Avoid contact with these elements in the event of a damaged muffler.

WARNING! Long term inhalation of the ! engine’s exhaust fumes, chain oil mist and dust from sawdust can represent a

health risk.

WARNING! The ignition system of this ! machine produces an electromagnetic

field during operation. This field may under some circumstances interfere with pacemakers. To reduce the risk of serious or fatal injury, we recommend persons with pacemakers to consult their physician and the pacemaker manufacturer before operating this machine.

6 – English

WARNING! Never allow children to use or ! be in the vicinity of the machine. As the

machine is equipped with a spring- loaded stop switch and can be started by low speed and force on the starter handle, even small children under some circumstances can produce the force necessary to start the machine. This can mean a risk of serious personal injury. Therefore remove the spark plug cap when the machine is not under close supervision.

Important

IMPORTANT!

The machine is only designed for cutting wood.

You should only use the saw with the bar and chain combinations we recommend in the chapter Technical data.

Never use the machine if you are fatigued, while under the influence of alcohol or drugs, medication or anything that could affect your vision, alertness, coordination or judgement.

Wear personal protective equipment. See instructions under the heading Personal protective equipment.

Do not modify this product or use it if it appears to have been modified by others.

Never use a machine that is faulty. Carry out the checks, maintenance and service instructions described in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists. See instructions under the heading Maintenance.

Never use any accessories other than those recommended in this manual. See instructions under the headings Cutting equipment and Technical data.

CAUTION! Always wear protective glasses or a face visor to reduce the risk of injury from thrown objects. A chain saw is capable of throwing objects, such as wood chips, small pieces of wood, etc, at great force. This can result in serious injury, especially to the eyes.

WARNING! Running an engine in a ! confined or badly ventilated area can

result in death due to asphyxiation or carbon monoxide poisoning.

WARNING! Faulty cutting equipment or ! the wrong combination of bar and saw

chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data.

Image 6
Contents 445e TrioBrake Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherVibration damping system Stop switchRight hand guard MufflerCutting equipment General rulesCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Which could lead to serious, even fatal injuries Chain oilFilling with chain oil Needle bearing lubrication Checking chain lubricationChain drive sprocket Checking wear on cutting equipmentBar Assembly Fitting the bar and chainWorking with the chain Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageStarting and Stopping Starting and stoppingStarting Stopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsTree felling technique LimbingSafe distance Felling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cut How to avoid kickback What is kickback?Freeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Checking the inertia brake release Checking the brake triggerThrottle lockout Muffler StarterReplacing the starter cord Fitting the starter Tensioning the recoil springReplacing the return and drive springs Recoil spring aLubricating the bar tip sprocket Air filterSpark plug Needle bearing lubricationCooling system Air Injection centrifugal cleaningTemperature -5C 23F or colder Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Bar and chain combinationsSaw chain filing and file gauges 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsSímbolos en el manual de instrucciones Aclaracion DE LOS SimbolosSímbolos en la máquina Etiquetas que se encuentran en la motosierraIndice ÍndicePrecauciones de seguridad para usuarios de Introduccion Apreciado cliente¿QUE ES QUE? ¿Qué es qué en la motosierra?Instrucciones Generales DE Seguridad Medidas a tomar antes de utilizar una motosierra nuevaImportante Equipo de seguridad de la máquina Emplee siempre el sentido comúnEquipo de protección personal Freno de cadena con protección contra reculadasInstrucciones Generales DE Seguridad Fiador del acelerador Captor de cadenaBotón de parada Protección de la mano derechaSistema amortiguador de vibraciones SilenciadorEquipo de corte reductor de reculadas Equipo de corteReglas básicas EspadaExpresiones características de la espada y cadena Generalidades sobre el afilado de los dientes cortantesGeneralidades sobre el ajuste de la profundidad de corte Tensado de la cadena Lubricación del equipo de corte Repostaje de aceite para cadena de motosierraControl de la lubricación de la cadena Control del desgaste del equipo de corte Piñón de arrastre de la cadenaLubricación del cojinete de agujas ¡ATENCION! La mayoría de los¡ATENCION! Para manipular la cadena MontajeMontaje de la espada y la cadena Deben utilizarse guantes protectoresManipulacion DEL Combustible CarburanteTransporte y almacenamiento RepostajeSeguridad en el uso del combustible Almacenamiento prolongadoArranque Y Parada Arranque y paradaArranque Parada Instrucciones generales de trabajo Tecnica DE TrabajoAntes de utilizar la máquina Reglas básicas de seguridadReglas básicas Técnica básica de corte DesignacionesTécnica de tala DesramadoDistancia de seguridad Dirección de derribo Corte de ramas bajas y camino de retiradaCorte de indicación Corte de derribo Medidas preventivas de las reculadas Tratamiento de una tala fallida¿Qué es la reculada? Tronzado del tronco Mantenimiento GeneralidadesAjuste del carburador Control de la función de inercia Control del efecto de frenadoDetenerse inmediatamente Fiador del acelerador Silenciador Mecanismo de arranqueCambio del cordón de arranque Montaje del mecanismo de arranque Tensado del muelle de retornoCambio del muelle de retorno y el muelle de arrastre Muelle de retorno aEngrase del cabezal de rueda de la espada Filtro de aireBujía Lubricación del cojinete de agujasUtilización en invierno Sistema refrigeranteDepuración centrífuga Air Injection Temperaturas de -5C 23F o inferioresPrograma de mantenimiento Datos Tecnicos Datos técnicosCombinaciones de espada y cadena Afilado y calibres de afilado de la cadena de sierraGarantia DEL Sistema DE Control DE Emisiones SUS Derechos Y Obligaciones DE GarantiaPrecauciones de seguridad en reculadas Precauciones DE Seguridad DE LA Norma AmericanaPrecauciones de seguridad para usuarios de motosierras Otras precauciones de seguridad´z+S23¶6X¨ Page 1151181-96