Husqvarna 445e TrioBrake manual Starting and Stopping, Starting and stopping

Page 20

STARTING AND STOPPING

Starting and stopping

WARNING! Note the following before

!starting:

The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting.

Never start a chain saw unless the bar, chain and all covers are ﬁtted correctly. Otherwise the clutch can come loose and cause personal injuries.

Place the machine on ﬁrm ground. Make sure you have a secure footing and that the chain cannot touch anything.

Keep people and animals well away from the working area.

Starting

The chain brake should be activated when starting the chain saw. Activate the chain brake by pushing the front hand guard forwards.

Cold engine

Start position (1): Set the start/stop switch in the choke position by pulling the red control outward - upward (1).

Decompression valve (2): Press the valve to reduce the pressure in the cylinder and make starting easier. Once the machine has started the valve will automatically return to its original setting.

Air purge (3): Press the air purge diaphragm repeatedly until fuel ﬁlls the diaphragm (at least 6 times). The diaphragm need not be completely ﬁlled.

Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull ﬁrmly and rapidly until the engine ﬁres (4).

Push down the red choke control (5) as soon as the engine ﬁres which can be heard through a "puff" sound. Keep on pulling the cord powerfully until the engine starts.

Warm engine

When the chain saw is heated restart the saw only by pulling the cord powerfully until the engine starts (6).

Never wrap the starter cord around your hand

There is a simpliﬁed start reminder with illustrations to describe each step on the rear edge of the saw (A).

As the chain brake is still engaged the speed of the engine must be set to idling as soon as possible, this is achieved by disengaging the throttle lock. Disengagement is done by gently touching on the throttle trigger. This prevents unnecessary wear to the clutch, clutch drum and brake band.

Allow the machine to idle a few seconds before giving full throttle.

20 – English

Image 20

Contents 445e TrioBrake KEY to Symbols Symbols on the machineSymbols in the operator’s manual You will ﬁnd the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherStop switch Right hand guardVibration damping system MufﬂerCutting equipment designed to reduce kickback Cutting equipmentGeneral rules Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Filling with chain oil Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Checking chain lubrication Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentBar Working with the chain AssemblyFitting the bar and chain Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting Starting and StoppingStarting and stopping Stopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsSafe distance Tree felling techniqueLimbing Directional cuts Felling directionClearing the trunk and preparing your retreat Felling cut Freeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs General MaintenanceCarburetor adjustment Checking the inertia brake release Checking the brake triggerThrottle lockout Replacing the starter cord MufﬂerStarter Tensioning the recoil spring Replacing the return and drive springsFitting the starter Recoil spring aAir ﬁlter Spark plugLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Temperature -5C 23F or colderCooling system Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain ﬁling and ﬁle gauges050/1,3 mm 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsAclaracion DE LOS Simbolos Símbolos en la máquinaSímbolos en el manual de instrucciones Etiquetas que se encuentran en la motosierraPrecauciones de seguridad para usuarios de IndiceÍndice Introduccion Apreciado cliente¿QUE ES QUE? ¿Qué es qué en la motosierra?Importante Instrucciones Generales DE SeguridadMedidas a tomar antes de utilizar una motosierra nueva Emplee siempre el sentido común Equipo de protección personalEquipo de seguridad de la máquina Freno de cadena con protección contra reculadasInstrucciones Generales DE Seguridad Fiador del acelerador Captor de cadenaProtección de la mano derecha Sistema amortiguador de vibracionesBotón de parada SilenciadorEquipo de corte Reglas básicasEquipo de corte reductor de reculadas EspadaExpresiones características de la espada y cadena Generalidades sobre el aﬁlado de los dientes cortantesGeneralidades sobre el ajuste de la profundidad de corte Tensado de la cadena Control de la lubricación de la cadena Lubricación del equipo de corteRepostaje de aceite para cadena de motosierra Piñón de arrastre de la cadena Lubricación del cojinete de agujasControl del desgaste del equipo de corte ¡ATENCION! La mayoría de losMontaje Montaje de la espada y la cadena¡ATENCION! Para manipular la cadena Deben utilizarse guantes protectoresManipulacion DEL Combustible CarburanteRepostaje Seguridad en el uso del combustibleTransporte y almacenamiento Almacenamiento prolongadoArranque Arranque Y ParadaArranque y parada Parada Tecnica DE Trabajo Antes de utilizar la máquinaInstrucciones generales de trabajo Reglas básicas de seguridadReglas básicas Técnica básica de corte DesignacionesDistancia de seguridad Técnica de talaDesramado Corte de indicación Dirección de derriboCorte de ramas bajas y camino de retirada Corte de derribo ¿Qué es la reculada? Medidas preventivas de las reculadasTratamiento de una tala fallida Tronzado del tronco Ajuste del carburador MantenimientoGeneralidades Detenerse inmediatamente Control de la función de inerciaControl del efecto de frenado Fiador del acelerador Cambio del cordón de arranque SilenciadorMecanismo de arranque Tensado del muelle de retorno Cambio del muelle de retorno y el muelle de arrastreMontaje del mecanismo de arranque Muelle de retorno aFiltro de aire BujíaEngrase del cabezal de rueda de la espada Lubricación del cojinete de agujasSistema refrigerante Depuración centrífuga Air InjectionUtilización en invierno Temperaturas de -5C 23F o inferioresPrograma de mantenimiento Datos Tecnicos Datos técnicosCombinaciones de espada y cadena Aﬁlado y calibres de aﬁlado de la cadena de sierraGarantia DEL Sistema DE Control DE Emisiones SUS Derechos Y Obligaciones DE GarantiaPrecauciones DE Seguridad DE LA Norma Americana Precauciones de seguridad para usuarios de motosierrasPrecauciones de seguridad en reculadas Otras precauciones de seguridad´z+S23¶6X¨ Page 1151181-96