Husqvarna Pro 15 manual Lever for adjustment of the cutting height, Parking brake, Seat, Fuelling

Page 15
Lever for adjustment of the cutting height

PRESENTATION

Lever for adjustment of the cutting height

The cutting height can be adjusted to 9 different positions with the cutting height lever.

Cutting unit with side/rear ejector,

40-90 mm.

BioClip cutting unit,

45-95 mm.

Parking brake

The parking brake is applied as follows:

1.Push down the brake pedal (1).

2.Fully depress the lock button on the steering column (2).

3.Release the brake pedal while holding the button pressed.

The parking brake lock disengages automatically when the brake pedal is pressed.

Seat

The seat has a jointed attachment on the front edge and can be tipped forward.

The seat can also be adjusted lengthways.

To adjust move the lever under the front edge of the seat to the left, so that the seat can be moved forward or backwards to the required position.

Fuelling

The engine runs on unleaded petrol with a mini- mum octane rating of 87 (not mixed with oil). We recommend the use of Aspen biodegradable alkylate petrol. Refer to the “Technical data” for information on methanol and ethanol fuels.

WARNING!

Petrol is highly inflammable. Exercise care and refuel outdoors (see safety instructions).

2

Parking brake 1 Seat

14 – English

Image 15
Contents 101 Rider ProOperator´s manual IMPORTANT INFORMATION CONTENTS Operator’s Manual for Rider ProII. Slope operation SAFETY INSTRUCTIONSSafe operation practices for ride-on mowers I. General operationIntended use IV. ServiceTravel and transport on public roads TowingTowing INSTRUCTIONDear customer Driving and transport on public roadsSerial number Good serviceEXPLANATION OF SYMBOLS Never carry passengers General useRead the instructions before starting the machine Clear the area from stones etc. before cuttingCut slopes upwards and downwards, not sideways Be extra careful when driving on slopesDriving on slopes Do as followsNever allow children to drive the machine MaintenanceChildren Keep children away from the mowing areaDo not alter the setting of the governor and do not race the engine Never smoke in the vicinity of the battery or the fuelClean the machine regularly from grass, leaves and other waste Never drive the machine in an enclosed spacePRESENTATION PresentationLocation of the controls Throttle control Choke leverSpeed limiter Cutting unit Lift lever for cutting unitLifting of the cutting unit Lowering of the cutting unit Fuelling Lever for adjustment of the cutting heightParking brake SeatDRIVING Before startingStarting the engine Driving the machine Mowing pattern Cutting tipsRelease lever Stopping the engineMaintenance interval in MAINTENANCEMaintenance schedule MaintenanceThe cutting unit is disengaged The engine is switched offThe parking brake is applied The ignition key is removedRight-hand fender Removing of the machine hoodsEngine hood Front hoodTransmission cover Checking and adjustment of the steering wiresPoorly adjusted brakes can result in reduced braking power Adjusting the brakesChecking and adjustment of the throttle wire Checking and adjusting the choke wireChecking of the fuel pump’s air filter Replacement of the fuel filterDo not use compressed air to clean the paper filter Replacing the air filterDo not wash the paper filter Do not oil the paper filter Muffler air intake Cleaning the filterCheck the transmission’s air intake Check the engine’s cooling air intakeProcedures on contact with acid Check the level of the battery acidInspecting the safety system Checking the tyre pressure The tyre pressure should be 60 kPa 0.6 kp/cm2 all roundThe maximum tyre pressure is 80 kPa 0,8 kp/cm2 Fitting the cutting unit Installing BioClip Checking and adjustment of the cutting unit’s ground pressureBioClip Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitRemoving the belt Removing the cutting unitBioClip 103 Versions 1 and BioClip 103 Versions 1 and Belt replacement on the BioClipProtect your hands by wearing gloves when working with the blades Replacing the cutting unit’s beltsBelt replacement on cutting unit’s with side or rear ejectors Belt replacement on BioClipPlacing in service position Service position for cutting unit5. Disengage the spring from the drive belt tensioning wheel Restoring from service position Checking the blades Cutting units with rear ejection Cutting units with side ejectionBioClip103 BioClip Replacing the break-pin BioClip 1/52 1/365 Lubrication chartLUBRICATION 12/12 1/12Lubricating wires General1. Cutting unit 2. Pedal mechanism in frame tunnel 3. Chains in frame tunnel4. Triangular link and joints 6. Throttle and choke wires, lever bearings 5. Driver’s seat7. Belt tensioner 8. Engine oil Changing the engine oilFULL 10. Parking brake wire 9. Gear lever11. Transmission oil level Avoid skin contact, wash with soap and water in the event of spillage 12. Transmission13. Replacing the oil filter IMPORTANT INFORMATION Dispose of used filters at a recycling stationTROUBLE SHOOTING SCHEDULE ProblemProcedure Service STORAGEWinter storage Explanation of colour abbreviations in wiring diagram WIRING DIAGRAM1. Microswitch, hydrostatic transmission 2. Microswitch, cutting unit 3. Microswitch, seat 4. Ignition lock 5. Counter 6. Start relayElectrical system TECHNICAL DATARider Pro EngineRear ejector EU declaration of conformity Only applies to EuropeBioClip Side ejectorSERVICEJOURNAL Pre-delivery serviceWork done 54 - English 25 hour service50 hour service 56 - English 100/200 hour service300 hour service 58 - English At least once a seasonDate, mileage, stamp, sign 60 - English ´*3-Q¶5w¨Page 2001W02