Husqvarna Pro 15 manual At least once a season, Servicejournal, Work done, English

Page 59

SERVICEJOURNAL

Work done

Date, mileage, stamp, sign

At least once a season

1.Change engine oil (100 hours).

2.Clean / replace the air filter pre-filter (oil-foam element) (25 hours).

(more regularly in dusty conditions)

3.Clean / replace the paper air filter (100 hours). (more regularly in dusty conditions).

4.Clean the fuel pump air filter (50 hours).

5.Check/adjust cutting height setting (50 hours).

6.Check/adjust parking brake (50 hours).

7.Inspect flame guard/spark arrestor, optional equipment (50 hours).

8.Replace engine oil filter (200 hours).

9.Clean/replace spark plug (100 hours).

10.Replace fuel filter in fuel line (100 hours).

11.Clean pulse-air filter (100 hours).

12.Clean the cooling flanges on the cylinders and cylinder head (100 hours).

(more regularly in dusty conditions).

13.Check engine valve clearance (300 hours).

14.Replace oil in K62 gearbox (500 hours).

15.Carry out 300 hour service at authorised dealer.

58 – English

Image 59

Contents Operator´s manual 101Rider Pro IMPORTANT INFORMATION CONTENTS Operator’s Manual for Rider ProII. Slope operation SAFETY INSTRUCTIONSSafe operation practices for ride-on mowers I. General operationIntended use IV. ServiceTravel and transport on public roads TowingTowing INSTRUCTIONDear customer Driving and transport on public roadsSerial number Good serviceEXPLANATION OF SYMBOLS Never carry passengers General useRead the instructions before starting the machine Clear the area from stones etc. before cuttingCut slopes upwards and downwards, not sideways Be extra careful when driving on slopesDriving on slopes Do as followsNever allow children to drive the machine MaintenanceChildren Keep children away from the mowing areaDo not alter the setting of the governor and do not race the engine Never smoke in the vicinity of the battery or the fuelClean the machine regularly from grass, leaves and other waste Never drive the machine in an enclosed spaceLocation of the controls PRESENTATIONPresentation Speed limiter Throttle controlChoke lever Lifting of the cutting unit Lowering of the cutting unit Cutting unitLift lever for cutting unit Fuelling Lever for adjustment of the cutting heightParking brake SeatStarting the engine DRIVINGBefore starting Driving the machine Mowing pattern Cutting tipsRelease lever Stopping the engineMaintenance interval in MAINTENANCEMaintenance schedule MaintenanceThe cutting unit is disengaged The engine is switched offThe parking brake is applied The ignition key is removedRight-hand fender Removing of the machine hoodsEngine hood Front hoodTransmission cover Checking and adjustment of the steering wiresPoorly adjusted brakes can result in reduced braking power Adjusting the brakesChecking and adjustment of the throttle wire Checking and adjusting the choke wireChecking of the fuel pump’s air filter Replacement of the fuel filterDo not wash the paper filter Do not oil the paper filter Do not use compressed air to clean the paper filterReplacing the air filter Muffler air intake Cleaning the filterCheck the transmission’s air intake Check the engine’s cooling air intakeProcedures on contact with acid Check the level of the battery acidInspecting the safety system The maximum tyre pressure is 80 kPa 0,8 kp/cm2 Checking the tyre pressureThe tyre pressure should be 60 kPa 0.6 kp/cm2 all round Fitting the cutting unit BioClip Installing BioClipChecking and adjustment of the cutting unit’s ground pressure Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitRemoving the belt Removing the cutting unitBioClip 103 Versions 1 and BioClip 103 Versions 1 and Belt replacement on the BioClipProtect your hands by wearing gloves when working with the blades Replacing the cutting unit’s beltsBelt replacement on cutting unit’s with side or rear ejectors Belt replacement on BioClipPlacing in service position Service position for cutting unit5. Disengage the spring from the drive belt tensioning wheel Restoring from service position BioClip103 BioClip Checking the bladesCutting units with rear ejection Cutting units with side ejection Replacing the break-pin BioClip 1/52 1/365 Lubrication chartLUBRICATION 12/12 1/121. Cutting unit Lubricating wiresGeneral 4. Triangular link and joints 2. Pedal mechanism in frame tunnel3. Chains in frame tunnel 7. Belt tensioner 6. Throttle and choke wires, lever bearings5. Driver’s seat FULL 8. Engine oilChanging the engine oil 11. Transmission oil level 10. Parking brake wire9. Gear lever Avoid skin contact, wash with soap and water in the event of spillage 12. Transmission13. Replacing the oil filter IMPORTANT INFORMATION Dispose of used filters at a recycling stationProcedure TROUBLE SHOOTING SCHEDULEProblem Winter storage ServiceSTORAGE Explanation of colour abbreviations in wiring diagram WIRING DIAGRAM1. Microswitch, hydrostatic transmission 2. Microswitch, cutting unit 3. Microswitch, seat 4. Ignition lock 5. Counter 6. Start relayElectrical system TECHNICAL DATARider Pro EngineRear ejector EU declaration of conformity Only applies to EuropeBioClip Side ejectorWork done SERVICEJOURNALPre-delivery service 54 - English 25 hour service50 hour service 56 - English 100/200 hour service300 hour service 58 - English At least once a seasonDate, mileage, stamp, sign 60 - English ´*3-Q¶5w¨Page 2001W02