Husqvarna Pro 15 manual Explanation Of Symbols

Page 7

EXPLANATION OF SYMBOLS

EXPLANATION OF SYMBOLS

These symbols are on the machine and in the instructions.

Study them carefully so that you know what they mean.

Read the instructions.

R N

Reverse

Neutral

Fast

Slow

Engine off

Battery

Choke

Fuel

Oil pressure

Cutting height

Backwards

Forwards

Ignition

Use hearing protection

Hydrostatic freewheel

Parking brake

Brake

Warning

Sound level	Warning! Rotating blades	Warning! Risk that the	Never drive across	European standard for
		machine can tip over	a slope	machine safety

Never use the machine if persons,	Never carry passengers on the
especially children, or animals,	machine or equipment
are in the vicinity

Starting instructions

Read the instructions

Check the engine’s oil level

Check the hydrostat’s oil level

Lift up the cutting unit

Hydrostatic pedals in neutral position

Brake

If the engine is cold use the choke

Start the engine

Release the parking brake before

driving

Keep hands and feet away	Drive very slowly
from under the hood when	without the cutting unit
the engine is running

Speed limiter pedal forwards

Neutral

Speed limiter pedal reverse

Switch off the engine and take off the ignition cable before repairs or maintenance

6 – English

Image 7

Contents Rider Pro 101Operator´s manual IMPORTANT INFORMATION CONTENTS Operator’s Manual for Rider ProII. Slope operation SAFETY INSTRUCTIONSSafe operation practices for ride-on mowers I. General operationIntended use IV. ServiceTravel and transport on public roads TowingTowing INSTRUCTIONDear customer Driving and transport on public roadsSerial number Good serviceEXPLANATION OF SYMBOLS Never carry passengers General useRead the instructions before starting the machine Clear the area from stones etc. before cuttingCut slopes upwards and downwards, not sideways Be extra careful when driving on slopesDriving on slopes Do as followsNever allow children to drive the machine MaintenanceChildren Keep children away from the mowing areaDo not alter the setting of the governor and do not race the engine Never smoke in the vicinity of the battery or the fuelClean the machine regularly from grass, leaves and other waste Never drive the machine in an enclosed spacePresentation PRESENTATIONLocation of the controls Choke lever Throttle controlSpeed limiter Lift lever for cutting unit Cutting unitLifting of the cutting unit Lowering of the cutting unit Fuelling Lever for adjustment of the cutting heightParking brake SeatBefore starting DRIVINGStarting the engine Driving the machine Mowing pattern Cutting tipsRelease lever Stopping the engineMaintenance interval in MAINTENANCEMaintenance schedule MaintenanceThe cutting unit is disengaged The engine is switched offThe parking brake is applied The ignition key is removedRight-hand fender Removing of the machine hoodsEngine hood Front hoodTransmission cover Checking and adjustment of the steering wiresPoorly adjusted brakes can result in reduced braking power Adjusting the brakesChecking and adjustment of the throttle wire Checking and adjusting the choke wireChecking of the fuel pump’s air filter Replacement of the fuel filterReplacing the air filter Do not use compressed air to clean the paper filterDo not wash the paper filter Do not oil the paper filter Muffler air intake Cleaning the filterCheck the transmission’s air intake Check the engine’s cooling air intakeProcedures on contact with acid Check the level of the battery acidInspecting the safety system The tyre pressure should be 60 kPa 0.6 kp/cm2 all round Checking the tyre pressureThe maximum tyre pressure is 80 kPa 0,8 kp/cm2 Fitting the cutting unit Checking and adjustment of the cutting unit’s ground pressure Installing BioClipBioClip Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitRemoving the belt Removing the cutting unitBioClip 103 Versions 1 and BioClip 103 Versions 1 and Belt replacement on the BioClipProtect your hands by wearing gloves when working with the blades Replacing the cutting unit’s beltsBelt replacement on cutting unit’s with side or rear ejectors Belt replacement on BioClipPlacing in service position Service position for cutting unit5. Disengage the spring from the drive belt tensioning wheel Restoring from service position Cutting units with rear ejection Cutting units with side ejection Checking the bladesBioClip103 BioClip Replacing the break-pin BioClip 1/52 1/365 Lubrication chartLUBRICATION 12/12 1/12General Lubricating wires1. Cutting unit 3. Chains in frame tunnel 2. Pedal mechanism in frame tunnel4. Triangular link and joints 5. Driver’s seat 6. Throttle and choke wires, lever bearings7. Belt tensioner Changing the engine oil 8. Engine oilFULL 9. Gear lever 10. Parking brake wire11. Transmission oil level Avoid skin contact, wash with soap and water in the event of spillage 12. Transmission13. Replacing the oil filter IMPORTANT INFORMATION Dispose of used filters at a recycling stationProblem TROUBLE SHOOTING SCHEDULEProcedure STORAGE ServiceWinter storage Explanation of colour abbreviations in wiring diagram WIRING DIAGRAM1. Microswitch, hydrostatic transmission 2. Microswitch, cutting unit 3. Microswitch, seat 4. Ignition lock 5. Counter 6. Start relayElectrical system TECHNICAL DATARider Pro EngineRear ejector EU declaration of conformity Only applies to EuropeBioClip Side ejectorPre-delivery service SERVICEJOURNALWork done 54 - English 25 hour service50 hour service 56 - English 100/200 hour service300 hour service 58 - English At least once a seasonDate, mileage, stamp, sign 60 - English ´*3-Q¶5w¨Page 2001W02