Husqvarna Pro 15 manual Servicejournal, Pre-delivery service, Work done

Page 54

SERVICEJOURNAL

SERVICEJOURNAL

Work done

Date, mileage, stamp, sign

Pre-delivery service

1. Top up battery with acid and recharge for four hours.

2. Fit steering wheel, seat and any optional equipment.

3. Fit cutting unit.

4. Adjust cutting unit:

Adjust lift springs (effective weight of cutting unit should be 12–15 kg, or set to maximum lift if brush is to be fitted).

Adjust cutting unit so that rear edge is about 2–4 mm higher than front edge.

Adjust cutting unit height setting so that cutting height limit is 5

mmabove the frame of the unit at the lowest cutting height.

5.Check that the oil levels in the engine and transmission are

correct.

6. Check and adjust tyre pressure (60 kPa, 0.6 bar).
7. Connect battery.
8. Fill with fuel and start engine.
9. Check that machine does not move in neutral.
10. Check:
Forward drive.
Reverse drive.
Operation of blades.
Seat safety switch.
Lift lever safety switch.
Safety switch for the hydrostat pedals.
11. Check engine revs 3,000 ±75 rpm.
12. Tell customer about:	Pre-delivery service carried out.
Need and benefits of following the service schedule.	No outstanding problems.
Need and benefits of following the service schedule.
Need and benefits of having machine serviced every 300	Certified:
Need and benefits of having machine serviced every 300
hours.
Servicing and the influence of this journal on the second-hand
value of the machine.
Range of applications for BioClip.
13. Complete proof of sale, etc.

After first 8 hours 1. Change engine oil.

English – 53

Image 54

Contents 101 Rider ProOperator´s manual CONTENTS Operator’s Manual for Rider Pro IMPORTANT INFORMATIONI. General operation SAFETY INSTRUCTIONSSafe operation practices for ride-on mowers II. Slope operationTowing IV. ServiceTravel and transport on public roads Intended useDriving and transport on public roads INSTRUCTIONDear customer TowingGood service Serial numberEXPLANATION OF SYMBOLS Clear the area from stones etc. before cutting General useRead the instructions before starting the machine Never carry passengersDo as follows Be extra careful when driving on slopesDriving on slopes Cut slopes upwards and downwards, not sidewaysKeep children away from the mowing area MaintenanceChildren Never allow children to drive the machineNever drive the machine in an enclosed space Never smoke in the vicinity of the battery or the fuelClean the machine regularly from grass, leaves and other waste Do not alter the setting of the governor and do not race the enginePRESENTATION PresentationLocation of the controls Throttle control Choke leverSpeed limiter Cutting unit Lift lever for cutting unitLifting of the cutting unit Lowering of the cutting unit Seat Lever for adjustment of the cutting heightParking brake FuellingDRIVING Before startingStarting the engine Driving the machine Cutting tips Mowing patternStopping the engine Release leverMaintenance MAINTENANCEMaintenance schedule Maintenance interval inThe ignition key is removed The engine is switched offThe parking brake is applied The cutting unit is disengagedFront hood Removing of the machine hoodsEngine hood Right-hand fenderChecking and adjustment of the steering wires Transmission coverChecking and adjusting the choke wire Adjusting the brakesChecking and adjustment of the throttle wire Poorly adjusted brakes can result in reduced braking powerReplacement of the fuel filter Checking of the fuel pump’s air filterDo not use compressed air to clean the paper filter Replacing the air filterDo not wash the paper filter Do not oil the paper filter Check the engine’s cooling air intake Cleaning the filterCheck the transmission’s air intake Muffler air intakeCheck the level of the battery acid Procedures on contact with acidInspecting the safety system Checking the tyre pressure The tyre pressure should be 60 kPa 0.6 kp/cm2 all roundThe maximum tyre pressure is 80 kPa 0,8 kp/cm2 Fitting the cutting unit Installing BioClip Checking and adjustment of the cutting unit’s ground pressureBioClip Adjusting the parallelism of the cutting unit Checking the cutting unit’s parallelismRemoving the cutting unit Removing the beltReplacing the cutting unit’s belts Belt replacement on the BioClipProtect your hands by wearing gloves when working with the blades BioClip 103 Versions 1 and BioClip 103 Versions 1 andBelt replacement on BioClip Belt replacement on cutting unit’s with side or rear ejectorsService position for cutting unit Placing in service position5. Disengage the spring from the drive belt tensioning wheel Restoring from service position Checking the blades Cutting units with rear ejection Cutting units with side ejectionBioClip103 BioClip Replacing the break-pin BioClip 12/12 1/12 Lubrication chartLUBRICATION 1/52 1/365Lubricating wires General1. Cutting unit 2. Pedal mechanism in frame tunnel 3. Chains in frame tunnel4. Triangular link and joints 6. Throttle and choke wires, lever bearings 5. Driver’s seat7. Belt tensioner 8. Engine oil Changing the engine oilFULL 10. Parking brake wire 9. Gear lever11. Transmission oil level IMPORTANT INFORMATION Dispose of used filters at a recycling station 12. Transmission13. Replacing the oil filter Avoid skin contact, wash with soap and water in the event of spillageTROUBLE SHOOTING SCHEDULE ProblemProcedure Service STORAGEWinter storage 3. Microswitch, seat 4. Ignition lock 5. Counter 6. Start relay WIRING DIAGRAM1. Microswitch, hydrostatic transmission 2. Microswitch, cutting unit Explanation of colour abbreviations in wiring diagramEngine TECHNICAL DATARider Pro Electrical systemSide ejector EU declaration of conformity Only applies to EuropeBioClip Rear ejectorSERVICEJOURNAL Pre-delivery serviceWork done 25 hour service 54 - English50 hour service 100/200 hour service 56 - English300 hour service At least once a season 58 - EnglishDate, mileage, stamp, sign ´*3-Q¶5w¨ 60 - EnglishPage 2001W02