Husqvarna Pro 15 manual CONTENTS Operator’s Manual for Rider Pro, Important Information

Page 2

CONTENTS

CONTENTS

Operator’s Manual for

Rider Pro 15

Safety instructions	2	Checking and adjustment of throttle wire	23
Safety rules for USA	2	Checking and adjusting the choke wire	23
Introduction	4	Replacement of fuel filter	24
Driving and transport on public roads	4	Checking the fuel pump’s air filter	24
Towing	4	Replacing the air filter	25
Use	4	Checking the transmission’s air intake	26
Serial number	5	Checking the engine’s cooling air intake	26
Explanation of symbols	6	Muffler air intake	26
Safety instructions	7	Check the level of the battery acid	27
General use	7	Check the safety system	28
Driving on slopes	8	Checking the tyre pressure	29
Children	9	Fitting the cutting unit	30
Maintenance	9	Installing BioClip 90	31
Presentation	11	Checking and adjustment of the cutting
Location of the controls	11	unit´s ground pressure	31
Throttle control	12	Checking the cutting unit´s parallelism	32
Choke lever	12	Adjusting the parallelism of the cutting unit ....	32
Speed limiter	12	Removing the cutting unit	33
Cutting unit	13	Removing the belts	33
Lift lever for cutting unit	13	Replacing the cutting unit’s belts	34
Lever for adjustment of cutting height	14	Service position for the cutting unit	36
Parking brake	14	Checking the blades	39
Seat	14	Replacing the break-pin (BioClip)	40
Fuelling	14	Lubrication	41
Driving	15	Lubrication chart	41
Before starting	15	General lubrication	42
Starting the engine	15	Lubricating wires	42
Driving the machine	16	Lubrication instructions according to chart	42
Cutting tips	17	Trouble shooting schedule	48
Stopping the engine	18	Storage	49
Disengage lever	18	Winter storage	49
Maintenance	19	Service	49
Maintenance schedule	19	Wiring diagram	50
Removing of the machine hoods	21	Technical data	51
Checking and adjusting the steering wires ....	22	Servicejournal	53
Adjusting the brakes	23

IMPORTANT INFORMATION

Read through these instructions carefully so that you know how to use and maintain the machine before using it.

For servicing other than described in this manual contact an authorised dealer for parts and service.

English – 1

Image 2

Contents Operator´s manual 101Rider Pro CONTENTS Operator’s Manual for Rider Pro IMPORTANT INFORMATIONI. General operation SAFETY INSTRUCTIONSSafe operation practices for ride-on mowers II. Slope operationTowing IV. ServiceTravel and transport on public roads Intended useDriving and transport on public roads INSTRUCTIONDear customer TowingGood service Serial numberEXPLANATION OF SYMBOLS Clear the area from stones etc. before cutting General useRead the instructions before starting the machine Never carry passengersDo as follows Be extra careful when driving on slopesDriving on slopes Cut slopes upwards and downwards, not sidewaysKeep children away from the mowing area MaintenanceChildren Never allow children to drive the machineNever drive the machine in an enclosed space Never smoke in the vicinity of the battery or the fuelClean the machine regularly from grass, leaves and other waste Do not alter the setting of the governor and do not race the engineLocation of the controls PRESENTATIONPresentation Speed limiter Throttle controlChoke lever Lifting of the cutting unit Lowering of the cutting unit Cutting unitLift lever for cutting unit Seat Lever for adjustment of the cutting heightParking brake FuellingStarting the engine DRIVINGBefore starting Driving the machine Cutting tips Mowing patternStopping the engine Release leverMaintenance MAINTENANCEMaintenance schedule Maintenance interval inThe ignition key is removed The engine is switched offThe parking brake is applied The cutting unit is disengagedFront hood Removing of the machine hoodsEngine hood Right-hand fenderChecking and adjustment of the steering wires Transmission coverChecking and adjusting the choke wire Adjusting the brakesChecking and adjustment of the throttle wire Poorly adjusted brakes can result in reduced braking powerReplacement of the fuel filter Checking of the fuel pump’s air filterDo not wash the paper filter Do not oil the paper filter Do not use compressed air to clean the paper filterReplacing the air filter Check the engine’s cooling air intake Cleaning the filterCheck the transmission’s air intake Muffler air intakeCheck the level of the battery acid Procedures on contact with acidInspecting the safety system The maximum tyre pressure is 80 kPa 0,8 kp/cm2 Checking the tyre pressureThe tyre pressure should be 60 kPa 0.6 kp/cm2 all round Fitting the cutting unit BioClip Installing BioClipChecking and adjustment of the cutting unit’s ground pressure Adjusting the parallelism of the cutting unit Checking the cutting unit’s parallelismRemoving the cutting unit Removing the beltReplacing the cutting unit’s belts Belt replacement on the BioClipProtect your hands by wearing gloves when working with the blades BioClip 103 Versions 1 and BioClip 103 Versions 1 andBelt replacement on BioClip Belt replacement on cutting unit’s with side or rear ejectorsService position for cutting unit Placing in service position5. Disengage the spring from the drive belt tensioning wheel Restoring from service position BioClip103 BioClip Checking the bladesCutting units with rear ejection Cutting units with side ejection Replacing the break-pin BioClip 12/12 1/12 Lubrication chartLUBRICATION 1/52 1/3651. Cutting unit Lubricating wiresGeneral 4. Triangular link and joints 2. Pedal mechanism in frame tunnel3. Chains in frame tunnel 7. Belt tensioner 6. Throttle and choke wires, lever bearings5. Driver’s seat FULL 8. Engine oilChanging the engine oil 11. Transmission oil level 10. Parking brake wire9. Gear lever IMPORTANT INFORMATION Dispose of used filters at a recycling station 12. Transmission13. Replacing the oil filter Avoid skin contact, wash with soap and water in the event of spillageProcedure TROUBLE SHOOTING SCHEDULEProblem Winter storage ServiceSTORAGE 3. Microswitch, seat 4. Ignition lock 5. Counter 6. Start relay WIRING DIAGRAM1. Microswitch, hydrostatic transmission 2. Microswitch, cutting unit Explanation of colour abbreviations in wiring diagramEngine TECHNICAL DATARider Pro Electrical systemSide ejector EU declaration of conformity Only applies to EuropeBioClip Rear ejectorWork done SERVICEJOURNALPre-delivery service 25 hour service 54 - English50 hour service 100/200 hour service 56 - English300 hour service At least once a season 58 - EnglishDate, mileage, stamp, sign ´*3-Q¶5w¨ 60 - EnglishPage 2001W02