Husqvarna 305 manual Garden example, Garden Example, Proposals for installation and settings

Contents HUSQVARNA AUTOMOWER 305 OPERATOR’S MANUAL Page TABLE OF CONTENTS Dealer’s telephone number MEMOSerial number PIN code Dealer 1.1Introduction 1.Introduction and safety1.INTRODUCTION AND SAFETY IMPORTANT INFORMATION1.2Symbols on the product 1.3Symbols in the Operator’s Manual Xxxxxx xxxxx xxxx xxxx xxxxx1.4Safety instructions Maintenance Transport2. Presentation 2. PRESENTATION2.1 What’s what? The numbers in the picture correspond toMowing technique 2.2 FunctionCapacity Working method 6.5 Security 3 on page Movement patternLocating the charging station Carry out the installation in the following steps 3. Installation3. INSTALLATION 3.1 Preparations3.2Installation of the charging station Ideal position of the charging station3. INSTALLATION Connecting the transformer Installation och anslutning av laddstation 3.3 Charging the battery Plan where to lay the boundary wire 3.INSTALLATION3.4Installation of the boundary wire 3. INSTALLATION Secondary Boundaries within the working areaSecondary areas areaPassages when mowing SlopesLaying out the boundary wire Loop for connecting the guide wireJoining the boundary wire 26 - English3.5Connecting the boundary wire 3.6 Installation of the guide wire Placement and connection of the guide wire Maximum 3.7 Checking the installation 3.8 First start-upand calibration Use Memo on page 4 to make a note of the PIN code3.9 Test docking with the charging station 4. USE 4.1 Charging a discharged battery4. Use Operation Charging/Standby 4.2 Using the timerExample Operation Charging/Standby4.4 Stopping 4.5 Switching off4.3 Starting Restart4.6 Adjusting the cutting height 5.Control panel 5.CONTROL PANEL1.HOME 5.1Operation selection5.2 Multi-choicebuttons 2.AUTO5.3 Numbers 5.4 Main switch5. CONTROL PANEL 6.1 Main menu 6.Menu functions6.MENU FUNCTIONS Browse between menusTimer 6. MENU FUNCTIONS6.2 Menu structure Installation•Work period 6.3 Timer•Reset timer •Work daysDrive past wire 6.4 Installation•Test settings Guide widthNarrow Remote startTest OUT Test settingsTest IN Change PIN code Drive past wire6.5 Security Security levelsNew loop signal Time & Date 6.6 SettingsReset customer setting Language7.GARDEN EXAMPLE Proposals for installation and settings7.Garden example Proposed installation and settings7. GARDEN EXAMPLE Area 8. Maintenance 8. MAINTENANCE8.3 After winter storage 8.2 Service8.1 Winter storage AutomowerChassis 8.4 CleaningUnderframe and blade disc Wheels8.7 Blades 8.5 Transport and removal8.6 In the case of thunderstorms BodyReplacing the battery 8.MAINTENANCE8.8 Battery 7.Turn the mower upside down 5.Pull out the battery by pulling on the strap6.Set the main switch to position 58 - English9.1 Messages 9.Trouble shooting9.TROUBLE SHOOTING Message9. TROUBLE SHOOTING No drive 9.2Indicator lamp in the charging station LightCause 9.3 SymptomSymptom Actionbut the blade disc Automower vibrerarAutomower moves does not rotate9.4Finding breaks in the loop wire a Switch connection A1 and Guide 4.a Assume that the indicator lamp blinked yellow in test a above. Reset all connections to their original positions. Then disconnect A2. Connect 5.When the break is found, the damaged section 68 - English11. Environmental information 10.Technical data10.TECHNICAL DATA DataEN 61000-6-3 emission 12.EU declaration of conformity12.EU DECLARATION OF CONFORMITY EN 61000-6-2 and EN 61000-6-1 immunityPage ORIGINAL INSTRUCTIONS 115 42