Husqvarna 305 Symptom, Cause, Action, The robotic lawn, mower has difficulty, docking with the

Contents HUSQVARNA AUTOMOWER 305 OPERATOR’S MANUAL Page TABLE OF CONTENTS MEMO Serial number PIN code DealerDealer’s telephone number IMPORTANT INFORMATION 1.Introduction and safety1.INTRODUCTION AND SAFETY 1.1Introduction1.2Symbols on the product Xxxxxx xxxxx xxxx xxxx xxxxx 1.3Symbols in the Operator’s Manual1.4Safety instructions Transport Maintenance2. PRESENTATION 2. PresentationThe numbers in the picture correspond to 2.1 What’s what?2.2 Function CapacityMowing technique Working method Movement pattern Locating the charging station6.5 Security 3 on page 3.1 Preparations 3. Installation3. INSTALLATION Carry out the installation in the following stepsIdeal position of the charging station 3.2Installation of the charging stationEnglish - Connecting the transformer Installation och anslutning av laddstation 3.3 Charging the battery 3.INSTALLATION 3.4Installation of the boundary wirePlan where to lay the boundary wire IMPORTANT INFORMATION area Boundaries within the working areaSecondary areas SecondarySlopes Passages when mowingLoop for connecting the guide wire Laying out the boundary wire26 - English Joining the boundary wire3.5Connecting the boundary wire 3.6 Installation of the guide wire Placement and connection of the guide wire Maximum 3.7 Checking the installation Use Memo on page 4 to make a note of the PIN code 3.8 First start-upand calibration3.9 Test docking with the charging station 4.1 Charging a discharged battery 4. Use4. USE Operation Charging/Standby 4.2 Using the timerExample Operation Charging/StandbyRestart 4.5 Switching off4.3 Starting 4.4 Stopping4.6 Adjusting the cutting height 5.CONTROL PANEL 5.Control panel2.AUTO 5.1Operation selection5.2 Multi-choicebuttons 1.HOME5.4 Main switch 5. CONTROL PANEL5.3 Numbers Browse between menus 6.Menu functions6.MENU FUNCTIONS 6.1 Main menuInstallation 6. MENU FUNCTIONS6.2 Menu structure Timer•Work days 6.3 Timer•Reset timer •Work periodGuide width 6.4 Installation•Test settings Drive past wireRemote start NarrowTest settings Test INTest OUT Security levels Drive past wire6.5 Security Change PIN codeNew loop signal Language 6.6 SettingsReset customer setting Time & DateProposed installation and settings Proposals for installation and settings7.Garden example 7.GARDEN EXAMPLE7. GARDEN EXAMPLE Proposals for installation and settings 8. MAINTENANCE 8. MaintenanceAutomower 8.2 Service8.1 Winter storage 8.3 After winter storageWheels 8.4 CleaningUnderframe and blade disc ChassisBody 8.5 Transport and removal8.6 In the case of thunderstorms 8.7 Blades8.MAINTENANCE 8.8 BatteryReplacing the battery 58 - English 5.Pull out the battery by pulling on the strap6.Set the main switch to position 7.Turn the mower upside downMessage 9.Trouble shooting9.TROUBLE SHOOTING 9.1 Messages9. TROUBLE SHOOTING No drive Light 9.2Indicator lamp in the charging stationAction 9.3 SymptomSymptom Causedoes not rotate Automower vibrerarAutomower moves but the blade disc9.4Finding breaks in the loop wire a Switch connection A1 and Guide 4.a Assume that the indicator lamp blinked yellow in test a above. Reset all connections to their original positions. Then disconnect A2. Connect 68 - English 5.When the break is found, the damaged sectionData 10.Technical data10.TECHNICAL DATA 11. Environmental informationEN 61000-6-2 and EN 61000-6-1 immunity 12.EU declaration of conformity12.EU DECLARATION OF CONFORMITY EN 61000-6-3 emissionPage 115 42 ORIGINAL INSTRUCTIONS