Husqvarna 305 Laying out the boundary wire, Loop for connecting the guide wire, Installation

Contents HUSQVARNA AUTOMOWER 305 OPERATOR’S MANUAL Page TABLE OF CONTENTS Serial number PIN code Dealer MEMODealer’s telephone number 1.INTRODUCTION AND SAFETY 1.Introduction and safety1.1Introduction IMPORTANT INFORMATION1.2Symbols on the product Xxxxxx xxxxx xxxx xxxx xxxxx 1.3Symbols in the Operator’s Manual1.4Safety instructions Transport Maintenance2. PRESENTATION 2. PresentationThe numbers in the picture correspond to 2.1 What’s what?Capacity 2.2 FunctionMowing technique Working method Locating the charging station Movement pattern6.5 Security 3 on page 3. INSTALLATION 3. InstallationCarry out the installation in the following steps 3.1 PreparationsIdeal position of the charging station 3.2Installation of the charging stationEnglish - Connecting the transformer Installation och anslutning av laddstation 3.3 Charging the battery 3.4Installation of the boundary wire 3.INSTALLATIONPlan where to lay the boundary wire IMPORTANT INFORMATION Secondary areas Boundaries within the working areaSecondary areaSlopes Passages when mowingLoop for connecting the guide wire Laying out the boundary wire26 - English Joining the boundary wire3.5Connecting the boundary wire 3.6 Installation of the guide wire Placement and connection of the guide wire Maximum 3.7 Checking the installation Use Memo on page 4 to make a note of the PIN code 3.8 First start-upand calibration3.9 Test docking with the charging station 4. Use 4.1 Charging a discharged battery4. USE Example 4.2 Using the timerOperation Charging/Standby Operation Charging/Standby4.3 Starting 4.5 Switching off4.4 Stopping Restart4.6 Adjusting the cutting height 5.CONTROL PANEL 5.Control panel5.2 Multi-choicebuttons 5.1Operation selection1.HOME 2.AUTO5. CONTROL PANEL 5.4 Main switch5.3 Numbers 6.MENU FUNCTIONS 6.Menu functions6.1 Main menu Browse between menus6.2 Menu structure 6. MENU FUNCTIONSTimer Installation•Reset timer 6.3 Timer•Work period •Work days•Test settings 6.4 InstallationDrive past wire Guide widthRemote start NarrowTest IN Test settingsTest OUT 6.5 Security Drive past wireChange PIN code Security levelsNew loop signal Reset customer setting 6.6 SettingsTime & Date Language7.Garden example Proposals for installation and settings7.GARDEN EXAMPLE Proposed installation and settings7. GARDEN EXAMPLE 7. GARDEN EXAMPLE 8. MAINTENANCE 8. Maintenance8.1 Winter storage 8.2 Service8.3 After winter storage AutomowerUnderframe and blade disc 8.4 CleaningChassis Wheels8.6 In the case of thunderstorms 8.5 Transport and removal8.7 Blades Body8.8 Battery 8.MAINTENANCEReplacing the battery 6.Set the main switch to position 5.Pull out the battery by pulling on the strap7.Turn the mower upside down 58 - English9.TROUBLE SHOOTING 9.Trouble shooting9.1 Messages Message9. TROUBLE SHOOTING No drive Light 9.2Indicator lamp in the charging stationSymptom 9.3 SymptomCause ActionAutomower moves Automower vibrerarbut the blade disc does not rotate9.4Finding breaks in the loop wire a Switch connection A1 and Guide 4.a Assume that the indicator lamp blinked yellow in test a above. Reset all connections to their original positions. Then disconnect A2. Connect 68 - English 5.When the break is found, the damaged section10.TECHNICAL DATA 10.Technical data11. Environmental information Data12.EU DECLARATION OF CONFORMITY 12.EU declaration of conformityEN 61000-6-3 emission EN 61000-6-2 and EN 61000-6-1 immunityPage 115 42 ORIGINAL INSTRUCTIONS