Husqvarna 305 manual Garden Example, Proposals for installation and settings, Area

Contents HUSQVARNA AUTOMOWER 305 OPERATOR’S MANUAL Page TABLE OF CONTENTS Serial number PIN code Dealer MEMODealer’s telephone number 1.Introduction and safety 1.INTRODUCTION AND SAFETY1.1Introduction IMPORTANT INFORMATION1.2Symbols on the product 1.3Symbols in the Operator’s Manual Xxxxxx xxxxx xxxx xxxx xxxxx1.4Safety instructions Maintenance Transport2. Presentation 2. PRESENTATION2.1 What’s what? The numbers in the picture correspond toCapacity 2.2 FunctionMowing technique Working method Locating the charging station Movement pattern6.5 Security 3 on page 3. Installation 3. INSTALLATIONCarry out the installation in the following steps 3.1 Preparations3.2Installation of the charging station Ideal position of the charging station3. INSTALLATION Connecting the transformer Installation och anslutning av laddstation 3.3 Charging the battery 3.4Installation of the boundary wire 3.INSTALLATIONPlan where to lay the boundary wire 3. INSTALLATION Boundaries within the working area Secondary areasSecondary areaPassages when mowing SlopesLaying out the boundary wire Loop for connecting the guide wireJoining the boundary wire 26 - English3.5Connecting the boundary wire 3.6 Installation of the guide wire Placement and connection of the guide wire Maximum 3.7 Checking the installation 3.8 First start-upand calibration Use Memo on page 4 to make a note of the PIN code3.9 Test docking with the charging station 4. Use 4.1 Charging a discharged battery4. USE 4.2 Using the timer ExampleOperation Charging/Standby Operation Charging/Standby4.5 Switching off 4.3 Starting4.4 Stopping Restart4.6 Adjusting the cutting height 5.Control panel 5.CONTROL PANEL5.1Operation selection 5.2 Multi-choicebuttons1.HOME 2.AUTO5. CONTROL PANEL 5.4 Main switch5.3 Numbers 6.Menu functions 6.MENU FUNCTIONS6.1 Main menu Browse between menus6. MENU FUNCTIONS 6.2 Menu structureTimer Installation6.3 Timer •Reset timer•Work period •Work days6.4 Installation •Test settingsDrive past wire Guide widthNarrow Remote startTest IN Test settingsTest OUT Drive past wire 6.5 SecurityChange PIN code Security levelsNew loop signal 6.6 Settings Reset customer settingTime & Date LanguageProposals for installation and settings 7.Garden example7.GARDEN EXAMPLE Proposed installation and settings7. GARDEN EXAMPLE 7. GARDEN EXAMPLE 8. Maintenance 8. MAINTENANCE8.2 Service 8.1 Winter storage8.3 After winter storage Automower8.4 Cleaning Underframe and blade discChassis Wheels8.5 Transport and removal 8.6 In the case of thunderstorms8.7 Blades Body8.8 Battery 8.MAINTENANCEReplacing the battery 5.Pull out the battery by pulling on the strap 6.Set the main switch to position7.Turn the mower upside down 58 - English9.Trouble shooting 9.TROUBLE SHOOTING9.1 Messages Message9. TROUBLE SHOOTING No drive 9.2Indicator lamp in the charging station Light9.3 Symptom SymptomCause ActionAutomower vibrerar Automower movesbut the blade disc does not rotate9.4Finding breaks in the loop wire a Switch connection A1 and Guide 4.a Assume that the indicator lamp blinked yellow in test a above. Reset all connections to their original positions. Then disconnect A2. Connect 5.When the break is found, the damaged section 68 - English10.Technical data 10.TECHNICAL DATA11. Environmental information Data12.EU declaration of conformity 12.EU DECLARATION OF CONFORMITYEN 61000-6-3 emission EN 61000-6-2 and EN 61000-6-1 immunityPage ORIGINAL INSTRUCTIONS 115 42