RJ-45 Connector Pin Assignments | 3Com 10/100BASE-T4 guide

A-6 APPENDIX A: CABLING

RJ-45 Connector Pin Assignments

Figure A-1 shows the RJ-45 connector pin assignments.

BI_DI4–(8) BI_DI4+(7)

RD–(6) BI_DI3–(5) BI_DI3+(4)

RD+(3)

TD–(2)

TD+(1)

8

7

6

5

4

3

2

1

T4

T4

12 345678

Figure A-1 RJ-45 Connector Pin Assignments

Image 49

3Com 10/100BASE-T4 manual RJ-45 Connector Pin Assignments, Figure A-1 shows the RJ-45 connector pin assignments

Contents

Network Adapter Fast Etherlink Parallel TaskingUser Guide Adapters 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Lifetime Warranty Asia Contents Configuring Software Settings Cispr B Compliance Figures Tables About this Guide How to Use This GuideIntroduction Print Autolink.log Conventions Introduction Adapter automatically senses and switches to either 10/100BASE-T4 PCI Adapter Adapter Features PCI Technology Inspecting the Adapter Installing the Adapter3C59X EtherDisk diskette version 5.1 or above Installing the Adapter Installing the Boot Prom PCI Computer with PCI and Eisa Slots Connecting to the Network RJ-45 connector Connecting to the Network Loading the Network Summary of Driver Loading ProceduresDrivers Accessing DOS Using the EtherDisk Diskette Using Windows System Properties box appears, detailing your system setup Conﬁrming Adapter Installation for WindowsName of the installed 3Com adapter appears, as follows This conﬁrms the adapter’s installation One Adapter in a Client Using NetWare ODIAutoLink Requirements At the prompt, type AutoLink InstallationAlternatively, at the prompt, type Read the screen and press Enter ESC=Cancel Multiple Adapters in a Client FEA0 Main menu appears Select Conﬁguration and Diagnostic Program and press Enter One or More Adapters in a Server Loading Ndis Drivers Auto Select Media Type Updating Ndis DriversFollow the instructions displayed in the subsequent screens Desktop Management Interface Transcend PC Link SmartAgent Driver Agents Troubleshooting with the Diagnostic Tests Performing Troubleshooting Diagnostic Tests Before Running the Tests After performing the diagnostic tests, reboot your computerTypes of Tests Fast EtherLink 10/100BASE-T4 PCI adapter Running the Group 1 Tests Starting the Diagnostic Program Running the Group 3 Test Setting Up an Echo Server 3C59XCFG Getting Help If a Test Fails To print the ﬁle, type Miscellaneous Checks Changing the Test SetupTo change the test parameters, follow these steps LED LEDs When properly connected to a 10BASE-T network, Pin assignments for the RJ-45 connectorCabling Adapter Cabling Requirements Twisted-Pair Cable 10BASE-T Speciﬁcations 10BASE-T Operation 100BASE-TX Operation 100BASE-T Standard100BASE-TX designates the Ieee 802.3 speciﬁcation for 100BASE-FX Operation 100BASE-T4 Operation Figure A-1 shows the RJ-45 connector pin assignments RJ-45 Connector Pin Assignments Settings To change the software option settings, follow these steps Changing Software SettingsType at the prompt Select Adapter Installed Adapters Press Tab to highlight OK. Press Enter Continue this procedure with any of the other options \CONFIG\3C595.SET Adapter Speciﬁcations Specifications 3Com Bulletin Board Service On-line Technical ServicesTechnical Support 3ComForum on CompuServe World Wide Web SiteTo use 3ComForum Log on to CompuServe Press Return to see the 3ComForum main menu Support from Your Network Supplier 3ComFacts Automated Fax ServiceLocal numbers are available within the following countries Details about recent conﬁguration changes, if applicable Returning Products for RepairTo obtain an RMA number, call or fax 100BASE-T Glossary Bus Auto Select Media Type EMM386 EIA/TIA MAC STP Numerics Index DOS Ndis Network Driver Optimization option setting B-2 Windows 3.X 3-3 Windows Limited Warranty 3Com Corporation Bayfront Plaza Interference Handbook CE Notice