Figures | 3Com 10/100BASE-T4 specs

FIGURES

1-1	10/100BASE-T4 PCI Adapter	1-2
2-1	PCI Computer with PCI and EISA Slots		2-3
2-2	Connecting Twisted-Pair Cable 2-4
3-1	AutoLink Information Screen	3-7
3-2	Main Menu 3-7
A-1	RJ-45 Connector Pin Assignments A-6
B-1	Multiple Adapter Option Conﬁguration		B-3
B-2	Changing Adapter Options	B-4

Image 8

3Com 10/100BASE-T4 manual Figures

Contents

Fast Etherlink Parallel Tasking Network AdapterUser Guide Adapters 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Lifetime Warranty Asia Contents Configuring Software Settings Cispr B Compliance Figures Tables Introduction How to Use This GuideAbout this Guide Conventions Print Autolink.log Adapter automatically senses and switches to either Introduction 10/100BASE-T4 PCI Adapter Adapter Features PCI Technology 3C59X EtherDisk diskette version 5.1 or above Installing the AdapterInspecting the Adapter Installing the Boot Prom Installing the Adapter Connecting to the Network PCI Computer with PCI and Eisa Slots RJ-45 connector Connecting to the Network Drivers Summary of Driver Loading ProceduresLoading the Network Using the EtherDisk Diskette Accessing DOS Using Windows Conﬁrming Adapter Installation for Windows System Properties box appears, detailing your system setupName of the installed 3Com adapter appears, as follows This conﬁrms the adapter’s installation AutoLink Requirements Using NetWare ODIOne Adapter in a Client Alternatively, at the prompt, type AutoLink InstallationAt the prompt, type ESC=Cancel Read the screen and press Enter Multiple Adapters in a Client FEA0 Select Conﬁguration and Diagnostic Program and press Enter Main menu appears Loading Ndis Drivers One or More Adapters in a Server Follow the instructions displayed in the subsequent screens Updating Ndis DriversAuto Select Media Type Transcend PC Link SmartAgent Driver Agents Desktop Management Interface Performing Troubleshooting Diagnostic Tests Troubleshooting with the Diagnostic Tests After performing the diagnostic tests, reboot your computer Before Running the TestsTypes of Tests Fast EtherLink 10/100BASE-T4 PCI adapter Starting the Diagnostic Program Running the Group 1 Tests Running the Group 3 Test Setting Up an Echo Server 3C59XCFG Getting Help If a Test Fails To print the ﬁle, type To change the test parameters, follow these steps Changing the Test SetupMiscellaneous Checks LEDs LED Pin assignments for the RJ-45 connector When properly connected to a 10BASE-T network,Cabling Adapter Cabling Requirements Twisted-Pair Cable 10BASE-T Operation 10BASE-T Speciﬁcations 100BASE-TX designates the Ieee 802.3 speciﬁcation for 100BASE-T Standard100BASE-TX Operation 100BASE-T4 Operation 100BASE-FX Operation RJ-45 Connector Pin Assignments Figure A-1 shows the RJ-45 connector pin assignments Settings Type at the prompt Changing Software SettingsTo change the software option settings, follow these steps Select Adapter Installed Adapters Continue this procedure with any of the other options Press Tab to highlight OK. Press Enter \CONFIG\3C595.SET Specifications Adapter Speciﬁcations Technical Support On-line Technical Services3Com Bulletin Board Service World Wide Web Site 3ComForum on CompuServeTo use 3ComForum Log on to CompuServe Press Return to see the 3ComForum main menu Local numbers are available within the following countries 3ComFacts Automated Fax ServiceSupport from Your Network Supplier To obtain an RMA number, call or fax Returning Products for RepairDetails about recent conﬁguration changes, if applicable Glossary 100BASE-T Auto Select Media Type Bus EIA/TIA EMM386 MAC STP Index Numerics DOS Ndis Network Driver Optimization option setting B-2 Windows 3.X 3-3 Windows Limited Warranty 3Com Corporation Bayfront Plaza Interference Handbook CE Notice