Reference for Netbuilder Family | 3Com 11.1 specification

REFERENCE FOR NETBUILDER FAMILY

SOFTWARE UPDATE PAGES

This section includes update pages with changes and additions to Reference for NETBuilder Family Software Version 11.1.

Place the update pages at the front of each speciﬁed chapter.

Image 57

3Com 11.1 manual Reference for Netbuilder Family

Contents

NETBuilder Family Software Version 11.1 Release Notes Bayfront Plaza 3Com CorporationSanta Clara, California 95052-8145 Contents Web Link Documentation Path Zmodem Time Out Known Problems Bcmfdinteg File Conversion ConsiderationsCPU Utilization Statistic Deleting ATM Neighbors NAT Proxy ARP RouteDiscovery Sdhlc Half-Duplex Mode Web Link Login SupportDisplaying Conﬁguration Proﬁles Dynamic Paths Limitations Accm Not Conﬁgurable CONFiguration Authentication Header AHConﬁguring IPsec How IPsec Works Policies StatPollInterval Encryption Netbuilder Software Version Release NotesPackages Contact 3Com or your network supplier Supported PC Flash Memory Cards New ProductsLists 3Comapproved vendors of the PC ﬂash memory card Approved 20 MB Flash Memory Cards VPN Features Layer Two Tunneling Protocol New FeaturesApproved Dram SIMMs Additional RAS Enhancements Extensible Authentication ProtocolDhcp Proxy Encryption Strength Summary of Encryption Strengths Virtual Circuit PrioritizationEncryption Key Algorithm Package ID Length IP Version 6 Phase Firewall EnhancementsBGP-4 Enhancements Frame Relay PVC Q.933 Support Ospf Not-So-Stubby-Area NssaData Over Voice B-Channel Isdn Speciﬁcation Boundary Router Remote LAN Detection Token Ring in Fast Ethernet Tife Features Ascii Boot56/64K CSU/DSU External Loopback NETBuilder Web Link Improvements Application Notes Upgrade Management Utilities and NETBuilder Upgrade LinkFlash Load Placing a Data Over Toggle the respective paths. Type Example New Features Application Notes NETBuilder II Software Features SoftwareVersion 11.1 for the NETBuilder bridge/router platforms NETBuilder II Firmware Requirements Other FeaturesNETBuilder II Firmware Requirements IBM Protocols SuperStack II NETBuilder SI Software Features 458 438 SuperStack II NETBuilder Ethernet and Token Ring Features Models Features Token RingMemory Requirements Models Features Token Ring WAN Protocols OfﬁceConnect NETBuilder Software FeaturesModel and Software Package 112 132 111 145 131 112 131 120 132 Additional OfﬁceConnect NETBuilder Models Software Features 117 137 116136 Memory Requirements Ruuhp111.1 Utilities for the Solaris 2.5 platformsUtilities for the HP-UX 10.x platforms Ruuaix111.1 NETBuilder Upgrade Management Utilities Etc/passwd. You must add an entry can be ignored Known Issues Bridge Static Routes PROﬁle ServiceDLSw SVCs Token Ring a non-source routed frame Dialog boxes will be fully visible without scrolling Supported Asynchronous Modems Ports in DCE ModeSupported Synchronous Modem Modems History, the PPP link does not come up IBM-Related Feature Settings for Token Ring Ports Token Ring Frame Copy Errors Frame Copy Errors under LAN Net Manager3Com Bridge/Routers and Supported Features Known Problems Interrupt the boot cycle and enter monitor mode This systemValue SHow !profileID -PROFILE CONFiguration Notation Known Problems ADD !v1 -PPP ARU user, password Limitations Number of TCP Connections Processor/Frame Relay Relay port is Access for LLC2 TrafﬁcFront-End IBM Boundary Routing Multilink PPP SpeedPort running PPP Snmp Management Sdlc Adjacent Link Service Point Source-RouteStations for Appn Source Route Software Update Pages Using Netbuilder Family Procedures in this section describe how to conﬁgure IPsec Configuring IpsecConﬁguring IPsec Replace with this chapter On bridge/router, 2 enter Creating an Encryption PolicyCreating a Security Policy On bridge/router 2, enter Manual key information, use For example, to create a new encryption key set, enter Conﬁdentiality and data integrity To disable Ipsec on port 1, enter Assign an IP address to the tunnel virtual port by entering Enable Layer 2 Tunnelling by enteringCreate a route between the two tunnel endpoints by entering Conﬁgure an Ipsec policy/security association by entering How IPsec Works Enable Layer 2 Tunnelling Pptp by enteringCreate a route between two tunnel endpoints by entering Intercepted and viewed How IPsec Works Configuring Ipsec Reference for Netbuilder Family CONFiguration Ipsec Service ParametersIpsec Service Parameters and Commands CONTrol KeySet ManualPOLicy ManualKeyInfo Policyname Name you assign to the policy you are adding Is assigned dynamically using Ipcp or DhcpBe all or ALL Srcipaddr/mask Phase of the encrypt-decrypt-encrypt Encrypt phases, and the second 8 bytes for the decryptSpecifies Cipher Block Chaining mode of the Data 239.255.255.254 Ipsec Service Parameters Rsvp Service Parameters REQuest MaxFlowRateRESerVation UDPEndcap SR Service Parameters AllRoutesPlace this page in front of Chapter ROUte ROUte SR Service Parameters SYS Service Parameters SYS Service Parameters StatPollInterval Weblink Service Parameters Weblink Service Parameters