Manuals / 3Com / Computer Equipment / Switch

3Com 4210 52-PORT, 4210 PWR 18-PORT, 4210 9-PORT, 4210 PWR 26-PORT, 4210 18-PORT Gnd Rxd Dsr Cts

Models: 4210 52-PORT 4210 PWR 18-PORT 4210 PWR 26-PORT 4210 PWR 9-PORT 4210 26-PORT 4210 9-PORT 4210 18-PORT

1 74

Download 74 pages 2.79 Kb

Page 33

Image 33

Connecting the Console Cable

33

Table 16 Console cable pinouts

RJ-45	Signal	Direction	DB9 (console)

4	CD

5	GND	—	5

6	RXD	<—	3

7	DSR

8	CTS

When you want to use the terminal to configure the switch, follow these steps to connect a terminal device to your switch using console cables:

1Plug the DB-9 female connector of the Console cable to the serial port of the PC or terminal where the switch is to be configured.

2Connect the RJ-45 connector of the Console cable to the Console port of the switch.

CAUTION: Pay attention to the mark on the Console port and be sure to plug the connector to the right port.

If the switch has been powered on:

■First connect the DB-9 connector of the Console cable to the PC before connecting the RJ-45 connector to the switch.

■Disconnect the DB-9 connector of the Console cable from the PC after disconnecting the RJ-45 connector from the switch.

Image 33

3Com 4210 52-PORT, 4210 PWR 18-PORT, 4210 9-PORT, 4210 PWR 26-PORT, 4210 18-PORT, 4210 26-PORT, 4210 PWR 9-PORT Gnd Rxd Dsr Cts

Contents

3Com Switch 4210 Family United States Government Legend 3Com Corporation Campus Drive Marlborough, MA USA Contents Regulatory Notices Obtaining Support for Your 3COM Products About this Guide Related Documentation Description of their features Wire-speed Layer 2 switchingProduct Introduction Overview Switch 4210 9-port PWR Front panel Introduction to Switch 4210 Family PWR Switches Rear panel Power systemSide panel Cooling system Front panel of a Switch 4210 18-port PWR Shows the front panel of the Switch 4210 26-port PWR model Switch 4210 26-port PWR units support AC input or DC input AC inputDC input-Rated voltage range -52 VDC to -56 VDC Front Panel LEDs Power LED10/100BASE-TX Autosensing Ethernet Port Status LED Mbps Uplink Port Status LED This section describes each Switch 4210 Family model Introduction to the Switch 4210 Family Non-PWR ModelsSwitch 4210 9-port Front panel Panel Status Switch 4210 18-port Front panel Switch 4210 cools off naturally Switch 4210 18-port model’s rear panel Switch 4210 26-port Front panel Switch 4210 26-port rear panel Switch 4210 52-port Front Panel Port LED Describes the 10/100Base-TX autosensing port’s Link/Act LEDDescribes the Speed LED on the 10/100Base-TX port Technical Specifications Technical specifications for the SwitchSwitch Model Port PWR Earthing Lead Technical specifications for the Switch 4210 PWR models SFP modules supported by the Switch SwitchSFP Modules Supported for Product Introduction Installing the Switch Installing the Switch Mount the front bracket to the device Screw Front Installing the switch in a 19-inch rack Installation completed Sequence Power-upReady for operation 4210 Redundant Power Supply Connecting a52 for a list of suggested solutions PWR LED Colors System Switch 4210 Circuit Breaker and Cable Ratings Power AvailabilityRectifiers No Rectifier Redundancy +1 Rectifier RPS Connection to the Switch Using Power over Ethernet RJ-45 Signal Direction DB9 console ConnectingConsole Cable Terminal, as shown in Figure GND RXD DSR CTS Installing the Switch Managing Your Switch Methods of Managing a Switch User ViewSystem View Refer to Setting Up Snmp Management on Setting Up YourConfigured IP information Need to Snmp Configuring IP Manually Automatically Configuring the IP Address using Dhcp Viewing Configured IPAutomatically Information User View Login Connecting to Console Port Manually Configuring IP InformationYou can manually configure the switch IP information by Connecting the Workstation to the Switch Once you have logged in you are automatically in User View Setting Up the Switch with IP Information Prerequisites Using the Web Interface Enter the system-viewcommand and Enter Using Command Line Interface using Telnet Management Where xxx.xxx.xxx.xxx is the IP address of the switchConsole Port Connection Network Telnet Management using Setting Up CommandSetting Up Web Line Interface String is private Setting Up SnmpNew community string up to 32 characters String to be removed Passwords Default UsersDefault Users User Default Name Password Access Level Problem Solving Indicated by LEDs Solving Problems Solving Hardware Problems Error message indicating that the SFP transceiver is faulty Solving Communication ProblemsIP Addressing How do you obtain a registered IP Address? Solving Fabric Formation Problems Problem Solving Null Modem Cable PIN-OUTSPC-AT Serial Cable RJ-45 to RS-232 25-pin Ethernet Port RJ-45 Pin Assignments 10/100 and 1000BASE-T RJ-45 connectionsPin assignments Obtaining Support for Your 3COM Products Contact Us Available for purchase from your 3Com resellerTelephone Technical Support and Repair Country Telephone Number US and Canada Telephone Technical Support and Repair Latin America Telephone Technical Support and Repair 3Com Network 3COM Network ManagementSupervisor Director Appendix C 3COM Network Management Management Suite 3Com EnterpriseIntegration Kit with HP OpenView Appendix C 3COM Network Management Important Safety Information Safety Information Wichtige Sicherheitsinformationen ’information de Sécurité Importante Información de Seguridad Importante Appendix D Redundant Power Supply Safety Information Importanti Informazioni di Sicurezza Ważne informacje o zabezpieczeniach Appendix D Redundant Power Supply Safety Information Regulatory Notices How to identify and resolve radio-TV interference problems Appendix D Redundant Power Supply Safety Information