Manuals / 3M / Kitchen Appliance / Food Saver

3M 40800 Safetydevices Of The Machine, Blade Guards, Emergency Stop Button, Circuit Breaker

Models: 40800

1 126

Download 126 pages 4.35 Kb

Page 35

10-SAFETY DEVICES OF THE MACHINE

10-SAFETY DEVICES OF THE MACHINE

10.1 Blade Guards

Both the top and bottom taping units have a blade guard. (See Manual 2: AccuGlide™ 3 Taping Heads - 3 inch).

WARNING

•To reduce the risk associated with sharp blade hazards:

−Keep hands and ﬁngers away from tape cutoff blades under orange blade guards. The blades are extremely sharp.

10.2 Emergency Stop Button

The box drive belts are turned on and off with the electrical switch on the side of the machine frame.

The machine electrical supply can be turned off by pressing the latching emergency stop switch. To restart machine, rotate the emergency stop switch clockwise to release the switch latch (Figure 10-1). Restart machine by Pushing the On/Off switch to the Off (O) position and then to the On (I) position.

Start/Stop

Button

Figure 10-2

10.3 Electric System / Circuit Breaker

The electric system is protected by a ground wire whose continuity has been tested during the ﬁnal inspection. The system is also subject to insulation and dielectric strength tests.

Circuit Breaker

The case sealer is equipped with a circuit breaker which trips if the motors are overloaded. Located inside the electrical enclosure on the side of the machine frame just below the machine bed, the circuit breaker has been pre-set and requires no further maintenance.

WARNING

•To reduce the risk associated with hazardous voltage:

−Position electrical cord away from foot and vehicle trafﬁc.

Figure 10-1

700aks-NA

23

WARNING

•To reduce the risk associated with mechanical and electrical hazards:

−Allow only properly trained and

qualiﬁed personnel to operate and service this equipment.

If circuit is overloaded and circuit breaker trips, unplug machine from electrical power:

1.Determine cause of overload and correct.

2.Plug in machine.

3.Press machine "On" (I) button to resume case sealing.

Important: The use of an extension cord is not recommended. However, if one is needed for temporary use, it must:

•Have a wire size of 1.5mm diameter [AWG 16]

•Have a maximum length of 30.5m [100 ft]

•Be properly grounded.

2011 October

Image 35

3M 40800 Safetydevices Of The Machine, Blade Guards, Emergency Stop Button, Start/Stop Button Figure, Circuit Breaker

Contents

with AdjustableImportant Safety Case Sealer3M Center, Building 220-5E-06 St. Paul, MN 3M Industrial Adhesives and TapesIndustrial Adhesives and Tapes Replacement Parts and Service InformationTo Our Customers Identification PlateTHIS PAGE IS BLANK Industrial Adhesives and Tapes Replacement Parts And Service InformationTo Our Customers AVAILABLE DIRECT FROMTHIS PAGE IS BLANK Page 700aks Adjustable Case SealerSafety Technical SpecificationsTHIS PAGE IS BLANK 11. Set-Upand Adjustments TABLE OF CONTENTS continued7. Installation 10. Safety devicesTHIS PAGE IS BLANK 14. Additional Instructions TABLE OF CONTENTS continued13. Maintenance 12. OperationLIST OF ABBREVIATIONS, ACRONYMS ABBREVIATIONS AND ACRONYMS1-INTRODUCTION 3M-MaticTM 700aks Adjustable Case Sealer, Type1-INTRODUCTION continued 1.1 Manufacturing Specifications / Description1.2.2 Manual Maintenance 1.2 How to Read and Use the Instruction Manual2011 October 2.2 Data for Technical Assistance and Service2-GENERALINFORMATION 2.1 Data Identifying Manufacturer and MachineContents—700aksAdjustable Case Sealer 2-GENERALINFORMATION continued 2.3 WarrantyFigure 3-SAFETY3.1 General Safety Information Figure 3.3 Table of WarningsFigure FigureFigure Figure Figure Figure•To reduce the risk associated with muscle strain •To reduce the risk associated with pinch hazards3.7 Residual Hazards 3.9Personal Safety Measures3.4Operators Qualifications See Section 3.5Number of Operatorsthe Main Operations on the Machine Skill 2a: Electrical Maintenance TechnicianSkill 2: Mechanical Maintenance Technician 3.11 Operators Skill Levels Required to PerformPower Switch Assembly Upper Taping Head Height AdjustmentHandle Emergency Stop Switch Assembly78-8095-1628-8 78-8070-1336-8 78-8062-4266-1 Leg Height Adjustment Label not shownFigure 3-10- Replacement Labels / 3M Part Numbers 78-8113-8912-94.Tape 4-SPECIFICATIONS1. Power Requirements 3.Operating ConditionsTape Application Leg Length – Optional 4-SPECIFICATIONS continued 6.Tape Roll Diameter9.Box Weight and Size Capacities 7.Tape Application Leg Length – StandardBOX LENGTH IN DIRECTION OF SEAL Specifications continuedMinimum/Maximum Box Height Combinations Case Height Range Illustration28.5 4-SPECIFICATIONS continued10. Machine Dimensions Right Side5.1 Shipment and Handling of Packed Machine and can be lifted by using a fork truckPackaging Overall Dimensions 5-SHIPMENT-HANDLING-STORAGE,TRANSPORTFigure 6-UNPACKING6.1 Uncrating Removal of Pallet•To reduce the risk associated with muscle strain 7-INSTALLATIONM6 Socket Head Wrench Adjustable Leg Figure 7.1 Operating Conditions7.5 Removal of Plastic TIes 7-INSTALLATION continued7.6 Assembly Completion Fig. 7-7A Crank Assembly Fig. 7-7B7.7 Completion of Taping Heads 7-INSTALLATION continued7.11Inspection of Phases For Three-MainPhases Only8.1 Description of the Working Cycle 8.2 Definition of Running ModeFigure Figure 8.3.1 Normal Stop Procedure 8-THEORYOF OPERATION9.4 Lockable Emergency Stop Button 9-CONTROLS 9.1 Box Width Adjusting Knobs Figure9.2 Box Height Adjusting Crank Figure 9.3 Start/Stop Buttons FigureStart/Stop Button Figure 10-SAFETYDEVICES OF THE MACHINE10.1 Blade Guards 10.2 Emergency Stop Button11.3 Adjustment of Top Flap Compression Rollers 11 - SET UP AND ADJUSTMENTS11.1 Box Width Adjustment 11.2 Box Height Adjustment305mm Minimum Figure 11 - SET UP AND ADJUSTMENTS continued FigureFigure Figure THIS PAGE IS BLANK 12.6 Cleaning 12.4 Tape Replacement and Threading12.5 Box Size Adjustment Section 11 - Set-Upand AdjustmentsCAUSE 12.9 Trouble Shooting GuidePROBLEM 12-OPERATION continuedCAUSE 12.9 Trouble Shooting Guide continuedPROBLEM 12-OPERATION continued13.6 Cleaning of Machine Qualification 13-MAINTENANCEAND REPAIRS13.1 Safety Measures see section 13.5 Check Efficiency of Safety FeaturesA C D Figure Upper Drive Belt Replacement 13-MAINTENANCEAND REPAIRS continued13.8Box Drive Belt Replacement E A BC D Figure 13-4Lower Drive Belt ReplacementFigure 13-MAINTENANCEAND REPAIRS continuedFigure 13-7Box Drive Belt Tension Adjustment 13.9Box Drive Pulley RingsBelts 13-MAINTENANCEAND REPAIRS continuedBox Drive M5 X 16 FlatTHIS PAGE IS BLANK ________ 14.1 Information for Disposal of Machine ELV 14.2 Emergency Procedures14-ADDITIONALINSTRUCTIONS 15-ENCLOSURES /SPECIAL INFO2011 October 16-TECHNICALDIAGRAMS 16.1 Electric Diagram700aks-NA 3M-PartNumber Spare Parts – 700aks Adjustable Case Sealer16.2 Spare Parts Order 700aksFrame Assemblies To Order Parts 700aks Adjustable Case Sealer, TypeOptions and Accessories Option/AccessoryTHIS PAGE IS BLANK Figure 700aksFigure Figure2011 October 700aksFigure 700aks-NA3M Part No 700aksFigure Ref. No2011 October 700aksFigure 700aks-NA3M Part No 700aksFigure Ref. No700aks-NA 3 22 24 23 10 11 7700aks Figure3M Part No 700aksFigure Ref. NoOption 2525700aks Caster3M Part No 700aksFigure343315245 Ref. No11 =12+13+14+15 700aks-NA2011 October 3M Part No 700aksFigure Ref. No45 31 42 24 23 5319 700aks4360 Figure 15247 /3M Part No 700aksFigure 15247 / Ref. No2011 October 700aksFigure 15247 / 700aks-NA3M Part No 700aksFigure 15247 / Ref. No2011 October 700aksFigure 15248 / 700aks-NA3M Part No 700aksFigure 15248 / Ref. No69 70 71 700aks33 41 51 40 36 35 40 38 43 41Description 700aks Figure 15248 /Ref. No 3M Part No15 15 14 12 8 1 7 3 10 9 2 700aks12 11 14 4 Figure3M Part No 700aksFigure Ref. No27 18 - 3M Part No 700aksFigure Ref. NoFigure 700aks Random Case Sealer15 9 10 15 10 9 1 12 8 13 4 23M Part No 700aksFigure Ref. NoTHIS PAGE IS BLANK Instructions and Parts List Important Safety Information3M-Matic AccuGlide Upper and Lower Taping Heads 3 InchPage Identiﬁcation Plate Replacement Parts and Service InformationTo Our Customers United StatesTHIS PAGE IS BLANK Industrial Adhesives and Tapes Replacement Parts And Service InformationTo Our Customers AVAILABLE DIRECT FROMTHIS PAGE IS BLANK Page Table of ContentsInstruction Manual AccuGlide Upper and Lower Taping Heads - 3 Inch TypePart Name Warranty Equipment Warranty and Limited RemedyTaping Head Contents AccuGlide 3 Upper Taping Head - 3 Inch, Type Intended UseTHIS PAGE IS BLANK General Information Taping Head ContentsHow to use this Manual Part Name•To reduce the risk associated with muscle strain Important SafeguardsExplanation of Signal Word Consequences OPERATING THIS EQUIPMENT78-8070-1335-0 Important Safeguards continuedFigure 1-1Replacement Labels/3M Part Numbers Upper Taping Head Label Lower Taping Head Label2.Tape Width 8.Taping Head DimensionsSpeciﬁcations 1.Tape130mm 5 1/8 Specifications continuedReceiving And Handling InstallationInstallation Guidelines Tape Width AdjustmentTape Adhesive Side OperationTape Drum Tape Supply RollOne-Way •To reduce the risk associated with muscle strainTape Loading – Upper Taping Head Tape Loading – Lower Taping HeadFigure 3-5– Tape Loading/Threading FigureFigure 3-4– Tape Loading/Threading Blade Oiler Pad MaintenanceFigure 4-1– Blade Replacement Blade GuardHex Socket Section View of Maintenance continuedCleaning Applying/Bufﬁng Roller ReplacementFigure AdjustmentsFigure 5-2– Tape Web Alignment Adjustment Nut Tape Latch Alignment – FigureOne-WayTension Roller Figure Adjustments continued0.5 - 0.9kg 1 - 2 lbs Adjusting Nut Applying Mechanism SpringTape Leg Length Adjustments continuedLeading Tape Leg Length Adjustment – Figure AssemblyCause TroubleshootingTroubleshooting Guide ProblemCause Troubleshooting continuedTroubleshooting Guide ProblemAccuGlide 3 Upper Taping Head - 3 Inch Spare Parts/Service InformationReplacement Parts and Service Recommended Spare PartsAccuGlide 3 Lower Taping Head - 3 Inch, Type Replacement Parts Illustrations and Parts ListsAccuGlide 3 Upper Taping Head - 3 Inch, Type Figure AccuGlide 3 -Tape Head AccuGlide 3 - 3 inch2012 January AccuGlide 3 -Figure 10932 – Upper Head AccuGlide 3 - 3 - NA3M Part No AccuGlide 3 -Figure 10932 – Upper Head Ref. No2012 January AccuGlide 3 -Figure 10929 – Upper and Lower Heads AccuGlide 3 - 3 - NA3M Part No AccuGlide 3 -Figure 10929 – Upper and Lower Heads Ref. NoFigure 10926 – Upper Head 2 7 7 71 57 8 7 6 7 43 AccuGlide 3 -3M Part No AccuGlide 3 -Figure 10926 – Upper Head Ref. No2012 January AccuGlide 3 -Figure 10930 – Upper and Lower Heads AccuGlide 3 - 3 - NA3M Part No AccuGlide 3 -Figure 10930 – Upper and Lower Heads Ref. NoFigure 10928 – Upper and Lower Heads 17 18 5 371514 9 AccuGlide 3 -3M Part No AccuGlide 3 -Figure 10928 – 3 Upper and Lower Heads Ref. No2012 January AccuGlide 3 -Figure 10402 – Upper and Lower Heads AccuGlide 3 - 3 - NA3M Part No AccuGlide 3 -Figure 10402 – 3 Latch Upper and Lower Heads Ref. No2012 January AccuGlide 3 -Figure 10931 – Lower Head AccuGlide 3 - 3 - NA3M Part No AccuGlide 3 -Figure 10931 – Lower Head Ref. NoAccuGlide 3 - 3 - NA 7 34 7 7 6 9 7 8 7AccuGlide 3 - Figure 10927 – Lower Head3M Part No AccuGlide 3 -Figure 10927 – Lower Head Ref. NoTHIS PAGE IS BLANK