10-SAFETY DEVICES OF THE MACHINE

10.1 Blade Guards

10.3 Electric System / Circuit Breaker

Both the top and bottom taping units have a blade guard. (See Manual 2: AccuGlide™ 3 Taping Heads - 3 inch).

WARNING

•To reduce the risk associated with sharp blade hazards:

−Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades are extremely sharp.

10.2Emergency Stop Button

The box drive belts are turned on and off with the electrical switch on the side of the machine frame.

The machine electrical supply can be turned off by pressing the latching emergency stop switch. To restart machine, rotate the emergency stop switch clockwise to release the switch latch. Restart machine by Pushing the On/Off switch to the Off (O) position and then to the On (I) position

(Figure 10-1).

WARNING

•To reduce the risk associated with hazardous voltage:

The electric system is protected by a ground wire whose continuity has been tested during the final inspection. The system is also subject to insulation and dielectric strength tests.

Circuit Breaker

The case sealer is equipped with a circuit breaker which trips if the motors are overloaded. Located inside the electrical enclosure on the side of the machine frame just below the machine bed, the circuit breaker has been pre-set and requires no further maintenance.

WARNING

•To reduce the risk associated with mechanical and electrical hazards:

−Allow only properly trained and

qualified personnel to operate and service this equipment.

Note: The case sealer has a circuit breaker located in the electrical enclosure on the machine frame. If circuit becomes overloaded and circuit breaker trips, unplug the machine electrical cord and determine cause of overload. After two minutes plug machine electrical cord into outlet and reset the circuit breaker by turning the On/Off switch to the Off (O) position and then to

−Position electrical cord away from foot and vehicle traffic.

E-Stop

Switch

the On (I) position.

Important: The use of an extension cord is not recommended. However, if one is needed for temporary use, it must:

•Have a wire size of 1.5mm diameter [AWG 16]

•Have a maximum length of 30.5m [100 ft]

•Be properly grounded.

 

Figure 10-1

 

 

 

 

 

2011 September

 

800a3-NA

 

 

 

22

Page 33 Page 35
Page 34
Image 34
3M 800a3 manual Safety Devices of the Machine, Blade Guards Electric System / Circuit Breaker, Emergency Stop Button
Page 33 Page 35

800a3 specifications

The 3M 800A3 is an advanced respiratory protective device designed to provide high-performance filtration and comfort for users in various environments. It is particularly beneficial for those working in industries such as construction, manufacturing, and healthcare, where exposure to airborne contaminants is a significant concern. The design and technology behind the 3M 800A3 reflect the company's commitment to innovation and safety.

One of the main features of the 3M 800A3 is its high-efficiency particulate air (HEPA) filtration system. This system is engineered to capture at least 99.97% of airborne particles, including dust, pollen, smoke, and other harmful substances. This level of efficiency ensures that users can work confidently, knowing they are protected against fine particulate matter that could pose health risks.

The 3M 800A3 also incorporates a unique ergonomic design that enhances comfort and wearability. The soft, adjustable straps allow for a customizable fit, which is essential for prolonged use. Additionally, the device features a lightweight construction that reduces fatigue, enabling users to maintain focus and productivity throughout their workday.

Another notable characteristic is its compatibility with various 3M filters and cartridges. This flexibility allows users to tailor their respiratory protection based on the specific hazards they may encounter. Whether dealing with chemical vapors, fumes, or particulates, the 3M 800A3 can be equipped with the appropriate combination of filters to ensure optimal safety.

Moreover, the 3M 800A3 is equipped with a low-profile design, which minimizes interference with other personal protective equipment, such as safety glasses or face shields. The thoughtful engineering behind this product takes into account the practical challenges faced by users in their work environments.

To further enhance user experience, the 3M 800A3 includes features such as an exhalation valve that allows for easier breathing and reduced heat buildup within the mask. This is particularly advantageous in high-temperature settings or while performing strenuous tasks.

In summary, the 3M 800A3 respirator is a state-of-the-art protective device that combines advanced filtration technology, ergonomic design, and compatibility with various filters. Its focus on comfort and efficiency makes it a valuable tool for professionals needing reliable respiratory protection in challenging conditions.
Top Page Image Contents