Manuals / 3M / Household Appliance / Fan

3M 800ab 39600 manual 3 - Box Drive Assembly, Infeed End

Models: 800ab 39600

1 56

Download 56 pages 25.85 Kb

Page 26

Image 26

Maintenance (Continued)

Figure 4-3 – Box Drive Assembly, Infeed End

5.Install the new belt around drive rollers and insert new pin. Pin must not extend beyond edge of belt.

Important – Before installing new drive belt, check the belt inside surface for drive direction arrows and install belt accordingly. If no arrows are shown, the belt may be installed either way.

6.To set drive belt tension, turn adjustment screws

(G) equally on both the upper and lower tension assemblies. Turn the screws clockwise to increase tension or counterclockwise to decrease tension. See Figure 4-3.

Use a force gauge to pull the belt outward 25 mm [1 inch] at midspan, as shown with a moderate pulling force of 3.5 kg [7 lbs].

7.Reverse procedures to reassemble the drive belt assembly.

Figure 4-4 – Box Drive Belt Tension Adjustment, Top View

Page 26

Image 26

3M 800ab 39600 manual 3 - Box Drive Assembly, Infeed End, 4 - Box Drive Belt Tension Adjustment, Top View

Contents

Important Safety Information AdjustableInstructions and Parts List 3M-Matic3M/Tape Dispenser Parts Replacement Parts and Service InformationTo Our Customers 241 Venture DriveTo Our Customers Replacement Parts And Service InformationSERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALS AVAILABLE DIRECT FROMSection I - 800ab Adjustable Case Sealer Table of Contents800ab Adjustable Case Sealer Type Instruction ManualSection II - AccuGlide II STD 2 Inch Taping Head Table of Contents ContinuedPage 3M-MaticTM 800ab Adjustable Case Sealer, Type Intended Use800ab Contents Figure 1-1 - Hands Warning Label Important SafeguardsThis safety alert symbol identifies important messages in this manual Figure 1-2 - Electrical Warning LabelFigure 1-4 - Stop and Off/On Labels The Safety Instructions label, shown inFigure 1-5 - Safety Instructions Label Figure 1-6 - Operating Notice LabelFigure 1-8 - Knife Warning Label Figure 1-9 - Tape Threading LabelTHIS PAGE IS BLANK 3. Operating Conditions 1. Power Requirements2. Operating Rate 4. TapeBox Size Specifications Continued9. Box Weight and Size Capacities Weight Box Length In Direction Of Seal Must Be Greater Than Box HeightMaximum Machine DimensionsMinimum THIS PAGE IS BLANK Receiving And Handling Installation and Set-UpFigure 2-1 - Roller Installation Machine Set-UpWARNING - Keep hands/fingers away from tape cut-off knife under Installation and Set-Up ContinuedFigure 2-2 - Cable Tie, Taping Head CAUTION - Machine weighs approximately 114 kg 250 pounds uncrated WARNING - To prevent shock and fire hazard Position extensionTHIS PAGE IS BLANK Operation Figure 3-1 - Case Sealer Components, Left Front ViewEmergency Stop Switch 2. Turn electrical supply off when machine is not in useElectrical On/Off Switch WARNINGSFigure 3-2 - Side Drive Belts will occur Figure 3-3 - Check AdjustmentBox Size Set-Up WARNING - Be sure all packaging materials and tools are removedBox Sealing Cleaning MaintenanceWARNING - Turn off electrical power supply and disconnect Figure 4-1 - Frame Lubrication Points Knife Replacement, Taping HeadCircuit Breaker WARNING - The following procedure must be performed bycould result Drive BeltsFigure 4-3 - Box Drive Assembly, Infeed End Figure 4-4 - Box Drive Belt Tension Adjustment, Top Viewcould result Drive Belt Tension AdjustmentsTaping Head Adjustments Drive Belt Assembly Height WARNING - Turn off electrical power and disconnect power cord fromWARNING - Use care when working near tape cut-off knife as knife is Figure 5-1 - Drive Belt Assembly, DisassemblySpecial Set-Up Procedure Continued Figure 5-2 - Drive Belt Assembly, ReassemblyProblem TroubleshootingTroubleshooting Guide Causedangerous voltages. Severe injury or equipment damage could result Electrical DiagramFigure 7 - Electrical Diagram Spare Parts 800ab Adjustable Case Sealer, TypeSpare Parts/Tools Tool KitPart Number Options/AccessoriesOption/Accessory With AccuGlide II STD 2 Inch Taping Head Replacement Parts Illustrations and Parts List800ab Adjustable Case Sealer, Type THIS PAGE IS BLANK 800ab Adjustable Case Sealer W/AccuGlide II STD 2 Inch Taping Head 800ab Assembly800ab Adjustable Case Sealer Description Ref. No3M Part No 800ab Adjustable Case Sealer Figure 6163/1 of 3M Part No Figure 6163 page 1 ofRef. No Description800ab Adjustable Case Sealer Figure 6163/2 of 3M Part No Figure 6163 page 2 ofRef. No Description800ab Adjustable Case Sealer Figure 6174/1 of 3M Part No Figure 6174 Page 1 ofRef. No Description800ab Adjustable Case Sealer Figure 6174/2 of 3M Part No Figure 6174 Page 2 ofRef. No Description800ab Adjustable Case Sealer Figure 6175/1 of 3M Part No Figure 6175 page 1 ofRef. No Description800ab Adjustable Case Sealer Figure 6175/2 of 3M Part No Figure 6175 page 2 ofRef. No Description800ab Adjustable Case Sealer Description Ref. No3M Part No 800ab Adjustable Case Sealer Description Ref. No3M Part No 800ab Adjustable Case Sealer Safety and Information Labels 3M Part No 800ab Safety and Information LabelsRef. No Description