Manuals / 3M / Household Appliance / Fan

3M 800ab 39600 manual Ref. No, 3M Part No, Description

Models: 800ab 39600

1 56

Download 56 pages 25.85 Kb

Page 44

Figure 6174 (Page 1 of 2)

Ref. No.	3M Part No.	Description
6174-1	78-8076-5380-9	Bed – Conveyor
6174-2	78-8076-5381-7	Leg Assembly – Inner, W/Stop
6174-3	78-8076-5382-5	Leg – Inner
6174-4	78-8060-8480-8	Pad – Foot
6174-5	78-8055-0867-4	Screw – Hex Hd, M8 x 30
6174-6	78-8017-9313-0	Nut –Self-Locking, M8
6174-7	78-8017-9318-9	Washer – Plain 8 mm
6174-8	78-8076-5383-3	Stop – Leg
6174-9	26-1003-7963-0	Screw – Soc Hd, M8 x 16
6174-10	78-8060-8481-6	Label – Height
6174-11	78-8052-6676-0	Clamp – Outer
6174-12	78-8052-6677-8	Clamp – Inner
6174-13	78-8060-7693-7	Roller – 32 x 38
6174-14	78-8076-5384-1	Shaft – Roller
6174-15	78-8076-5385-8	Spring
6174-16	78-8094-6100-3	Conveyor Assembly – Front
6174-17	78-8076-5387-4	Conveyor – Front
6174-18	78-8091-0780-4	Shaft – Central Roller
6174-19	78-8091-0781-2	Shaft – Side Roller
6174-20	26-1003-5828-7	Screw – Hex Hd, M6 x 10 Special
6174-21	78-8076-5389-0	Mounting – Conveyor
6174-22	78-8094-6101-1	Conveyor Assembly – Rear
6174-23	78-8076-5391-6	Conveyor – Rear
6174-24	78-8076-5392-4	Support – Tape Drum
6174-25	78-8060-8483-2	Support – Outboard Roll
6174-26	78-8060-8484-0	Shaft – Roller

39

Image 44

3M 800ab 39600 manual Ref. No, 3M Part No, Description

Contents

Adjustable Instructions and Parts ListImportant Safety Information 3M-MaticReplacement Parts and Service Information To Our Customers3M/Tape Dispenser Parts 241 Venture DriveReplacement Parts And Service Information SERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALSTo Our Customers AVAILABLE DIRECT FROMTable of Contents 800ab Adjustable Case Sealer TypeSection I - 800ab Adjustable Case Sealer Instruction ManualSection II - AccuGlide II STD 2 Inch Taping Head Table of Contents ContinuedPage 3M-MaticTM 800ab Adjustable Case Sealer, Type Intended Use800ab Contents Important Safeguards This safety alert symbol identifies important messages in this manualFigure 1-1 - Hands Warning Label Figure 1-2 - Electrical Warning LabelThe Safety Instructions label, shown in Figure 1-5 - Safety Instructions LabelFigure 1-4 - Stop and Off/On Labels Figure 1-6 - Operating Notice LabelFigure 1-8 - Knife Warning Label Figure 1-9 - Tape Threading LabelTHIS PAGE IS BLANK 1. Power Requirements 2. Operating Rate3. Operating Conditions 4. TapeSpecifications Continued 9. Box Weight and Size Capacities WeightBox Size Box Length In Direction Of Seal Must Be Greater Than Box HeightMaximum Machine DimensionsMinimum THIS PAGE IS BLANK Installation and Set-Up Figure 2-1 - Roller InstallationReceiving And Handling Machine Set-UpWARNING - Keep hands/fingers away from tape cut-off knife under Installation and Set-Up ContinuedFigure 2-2 - Cable Tie, Taping Head CAUTION - Machine weighs approximately 114 kg 250 pounds uncrated WARNING - To prevent shock and fire hazard Position extensionTHIS PAGE IS BLANK Operation Figure 3-1 - Case Sealer Components, Left Front View2. Turn electrical supply off when machine is not in use Electrical On/Off SwitchEmergency Stop Switch WARNINGSwill occur Figure 3-3 - Check Adjustment Box Size Set-UpFigure 3-2 - Side Drive Belts WARNING - Be sure all packaging materials and tools are removedBox Sealing Maintenance WARNING - Turn off electrical power supply and disconnectCleaning Figure 4-1 - Frame Lubrication Points Knife Replacement, Taping HeadWARNING - The following procedure must be performed by could resultCircuit Breaker Drive BeltsFigure 4-3 - Box Drive Assembly, Infeed End Figure 4-4 - Box Drive Belt Tension Adjustment, Top Viewcould result Drive Belt Tension AdjustmentsTaping Head Adjustments WARNING - Turn off electrical power and disconnect power cord from WARNING - Use care when working near tape cut-off knife as knife isDrive Belt Assembly Height Figure 5-1 - Drive Belt Assembly, DisassemblySpecial Set-Up Procedure Continued Figure 5-2 - Drive Belt Assembly, ReassemblyTroubleshooting Troubleshooting GuideProblem Causedangerous voltages. Severe injury or equipment damage could result Electrical DiagramFigure 7 - Electrical Diagram 800ab Adjustable Case Sealer, Type Spare Parts/ToolsSpare Parts Tool KitPart Number Options/AccessoriesOption/Accessory With AccuGlide II STD 2 Inch Taping Head Replacement Parts Illustrations and Parts List800ab Adjustable Case Sealer, Type THIS PAGE IS BLANK 800ab Adjustable Case Sealer W/AccuGlide II STD 2 Inch Taping Head 800ab Assembly800ab Adjustable Case Sealer Description Ref. No3M Part No 800ab Adjustable Case Sealer Figure 6163/1 of Figure 6163 page 1 of Ref. No3M Part No Description800ab Adjustable Case Sealer Figure 6163/2 of Figure 6163 page 2 of Ref. No3M Part No Description800ab Adjustable Case Sealer Figure 6174/1 of Figure 6174 Page 1 of Ref. No3M Part No Description800ab Adjustable Case Sealer Figure 6174/2 of Figure 6174 Page 2 of Ref. No3M Part No Description800ab Adjustable Case Sealer Figure 6175/1 of Figure 6175 page 1 of Ref. No3M Part No Description800ab Adjustable Case Sealer Figure 6175/2 of Figure 6175 page 2 of Ref. No3M Part No Description800ab Adjustable Case Sealer Description Ref. No3M Part No 800ab Adjustable Case Sealer Description Ref. No3M Part No 800ab Adjustable Case Sealer Safety and Information Labels 800ab Safety and Information Labels Ref. No3M Part No Description