Manuals / 3M / Household Appliance / Fan

3M 800ab 39600 manual could result Drive Belt Tension, Taping Head Adjustments

Models: 800ab 39600

1 56

Download 56 pages 25.85 Kb

Page 27

Adjustments

Adjustments

WARNING – Turn off electrical power supply and disconnect power cord from electrical supply before beginning adjustments. If power cord is not disconnected, severe injury to personnel

could result.

Drive Belt Tension

Tension adjustment of the drive belts may be required during normal operation. Belt tension must be adequate to positively move the box through the machine and they should run fully on the surface of the pulleys at each end of the frame. The idler pulleys on the infeed end are adjusted in or out to provide proper belt tension. Each belt is adjusted separately.

Belt tension is obtained by tightening the adjustment screw so that a moderate pulling force of 3.5 kg [7 lbs] applied at the midspan, as shown in Figure 4-4, will deflect the belt 25 mm [1 inch]. This will assure positive contact between the belt and the drive pulley on the discharge end of the taping head.

To adjust belts, see "Maintenance – Drive Belts", page 20.

Taping Head Adjustments

WARNING – Use care when working near tape cut-off knife on taping head as knife is extremely sharp. If care is not taken, severe injury to personnel could result.

TAPE WEB ALIGNMENT – Section II, page 11

TAPE DRUM FRICTION BRAKE – Section II, page 11

APPLYING MECHANISM SPRING – Section II, page 11

ONE-WAY TENSION ROLLER – Section II, page 12

TAPE LEG LENGTH

Leading Tape Leg Length Adjustment – Section II, page 13

Changing Tape Leg Length from 70 to 48 mm [2-3/4 to 2 Inches] – Section II, page 13.

Note – When changing tape leg to 48 mm [2 inches], refer also to Section I, "Special Set-Up Procedure – Changing Tape Leg Length", page 23.

22

Image 27

3M 800ab 39600 manual could result Drive Belt Tension, Taping Head Adjustments

Contents

3M-Matic AdjustableInstructions and Parts List Important Safety Information241 Venture Drive Replacement Parts and Service InformationTo Our Customers 3M/Tape Dispenser PartsAVAILABLE DIRECT FROM Replacement Parts And Service InformationSERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALS To Our CustomersInstruction Manual Table of Contents800ab Adjustable Case Sealer Type Section I - 800ab Adjustable Case SealerTable of Contents Continued PageSection II - AccuGlide II STD 2 Inch Taping Head Intended Use 3M-MaticTM 800ab Adjustable Case Sealer, Type800ab Contents Figure 1-2 - Electrical Warning Label Important SafeguardsThis safety alert symbol identifies important messages in this manual Figure 1-1 - Hands Warning LabelFigure 1-6 - Operating Notice Label The Safety Instructions label, shown inFigure 1-5 - Safety Instructions Label Figure 1-4 - Stop and Off/On LabelsFigure 1-9 - Tape Threading Label Figure 1-8 - Knife Warning LabelTHIS PAGE IS BLANK 4. Tape 1. Power Requirements2. Operating Rate 3. Operating ConditionsBox Length In Direction Of Seal Must Be Greater Than Box Height Specifications Continued9. Box Weight and Size Capacities Weight Box SizeMachine Dimensions MinimumMaximum THIS PAGE IS BLANK Machine Set-Up Installation and Set-UpFigure 2-1 - Roller Installation Receiving And HandlingInstallation and Set-Up Continued Figure 2-2 - Cable Tie, Taping HeadWARNING - Keep hands/fingers away from tape cut-off knife under WARNING - To prevent shock and fire hazard Position extension CAUTION - Machine weighs approximately 114 kg 250 pounds uncratedTHIS PAGE IS BLANK Figure 3-1 - Case Sealer Components, Left Front View OperationWARNINGS 2. Turn electrical supply off when machine is not in useElectrical On/Off Switch Emergency Stop SwitchWARNING - Be sure all packaging materials and tools are removed will occur Figure 3-3 - Check AdjustmentBox Size Set-Up Figure 3-2 - Side Drive BeltsBox Sealing Figure 4-1 - Frame Lubrication Points Knife Replacement, Taping Head MaintenanceWARNING - Turn off electrical power supply and disconnect CleaningDrive Belts WARNING - The following procedure must be performed bycould result Circuit BreakerFigure 4-4 - Box Drive Belt Tension Adjustment, Top View Figure 4-3 - Box Drive Assembly, Infeed EndAdjustments Taping Head Adjustmentscould result Drive Belt Tension Figure 5-1 - Drive Belt Assembly, Disassembly WARNING - Turn off electrical power and disconnect power cord fromWARNING - Use care when working near tape cut-off knife as knife is Drive Belt Assembly HeightFigure 5-2 - Drive Belt Assembly, Reassembly Special Set-Up Procedure ContinuedCause TroubleshootingTroubleshooting Guide ProblemElectrical Diagram Figure 7 - Electrical Diagramdangerous voltages. Severe injury or equipment damage could result Tool Kit 800ab Adjustable Case Sealer, TypeSpare Parts/Tools Spare PartsOptions/Accessories Option/AccessoryPart Number Replacement Parts Illustrations and Parts List 800ab Adjustable Case Sealer, TypeWith AccuGlide II STD 2 Inch Taping Head THIS PAGE IS BLANK 800ab Assembly 800ab Adjustable Case Sealer W/AccuGlide II STD 2 Inch Taping Head800ab Adjustable Case Sealer Ref. No 3M Part NoDescription 800ab Adjustable Case Sealer Figure 6163/1 of Description Figure 6163 page 1 ofRef. No 3M Part No800ab Adjustable Case Sealer Figure 6163/2 of Description Figure 6163 page 2 ofRef. No 3M Part No800ab Adjustable Case Sealer Figure 6174/1 of Description Figure 6174 Page 1 ofRef. No 3M Part No800ab Adjustable Case Sealer Figure 6174/2 of Description Figure 6174 Page 2 ofRef. No 3M Part No800ab Adjustable Case Sealer Figure 6175/1 of Description Figure 6175 page 1 ofRef. No 3M Part No800ab Adjustable Case Sealer Figure 6175/2 of Description Figure 6175 page 2 ofRef. No 3M Part No800ab Adjustable Case Sealer Ref. No 3M Part NoDescription 800ab Adjustable Case Sealer Ref. No 3M Part NoDescription 800ab Adjustable Case Sealer Safety and Information Labels Description 800ab Safety and Information LabelsRef. No 3M Part No